All Products

SKU: EC-CCH01065C

A 1×6 female stackable header with extra-long pins, designed for stacking Arduino shields. The extended legs pass through one shield's PCB and connect into the board below, allowing multiple shields to be stacked on top of each other. Specifications Pins: 6 (1×6 single row) Type: Female stack...

SKU: SF-PRT-11376

A 10-pin female header with extra-long legs, designed for stacking Arduino R3-compatible shields. The extended pins pass through a shield's PCB and connect to the board below, letting you stack multiple shields on a single Arduino. Key Features 10-Pin Female Header – Standard 0.1″ (2.54 mm) pi...

SKU: SF-DEV-18426

The MyoWare® 2.0 Arduino Shield is designed to easily connect up to six MyoWare 2.0 Muscle Sensors and Link Shields using 3.5mm TRS-to-TRS audio cables. The board comes pre-populated with male headers so all you would need to do is stack it on your Arduino and connect the sensors to read up to si...

SKU: DF-FIT0105

A pack of 10 long straight male header strips, each with 40 breakable pins at 2.54mm pitch. The extended 10mm pin length allows socket-to-socket connections, and the plastic separator can be repositioned along the pins to suit your application. Snap or cut the strips to any size needed for custo...

SKU: DF-FIT0165

An 8-pin female stackable header with extended legs, designed for stacking Arduino shields and prototyping boards. The extra-long pins pass through one board and connect to the next, making it easy to build multi-layer shield stacks. Standard 0.1-inch (2.54mm) pin spacing ensures compatibility w...

SKU: DF-FIT0031

A pack of 10 analog sensor cables designed for use with DFRobot IO Expansion Shields and compatible analog sensors. Each cable connects a sensor to the expansion shield's analog ports, making wiring quick and tidy. Each cable features a servo-type connector (Signal, GND, PWR) on one end and a 3-...

SKU: DF-FIT0008

This compact 170-point mini breadboard is ideal for small prototyping tasks and fits neatly onto Arduino proto shields, enclosures, or project bases thanks to its strong self-adhesive backing. The solderless tie points accept standard jumper wires and component leads for quick circuit assembly. ...

SKU: KI-2746

When using through hole LEDs it can be hard to form the eyelets and then work out which leg is positive and negative. That's where these Sewable LED Holders come in! The 5mm LED holder boards, quickly and easily take any through hole 5mm LED and (after soldering in place) make them easy to use in...

SKU: SF-PRT-11417

These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (2 8-pin, 1 10-pin and 1 6-pin), enough to connect a shield t...

SKU: EF-EF04033

The Octopus Button Switch Brick is a simple, plug-and-play pushbutton module from the ElecFreaks Octopus Electronic Bricks series. It features a large button with a transparent cap — you can insert a custom label underneath for easy identification in your projects. Designed for breadboard-free c...

SKU: SF-DEV-27924 · MPN: DEV-27924

Control a project with muscle activity instead of buttons, levers or joysticks. The MyoWare® 2.0 Muscle Sensor is an all-in-one surface electromyography (sEMG) sensor that detects the electrical signals generated when a muscle flexes, then outputs an analogue signal representing the strength of t...

SKU: EC-MCS02930M

This Adruino compatible motor Driver shield is a full-featured products that it can be used to drive 4 DC motor or two 4-wire stepper and two 5v servo. It drive the DC motor and stepper with the L293D,and it drive the servo with arduino pin9 and pin10. Features Be able to drive 4 DC motor and...

SKU: PL-2739

The Pololu AltIMU-10 v5 is a compact inertial measurement unit (IMU) and altimeter that combines a gyroscope, accelerometer, magnetometer, and barometric pressure sensor on a single board. It provides ten independent measurements — pressure, 3-axis rotation, 3-axis acceleration, and 3-axis magnet...

SKU: EF-EF04032

The Octopus Analog Photocell Brick is a light-dependent resistor (LDR) module from the ElecFreaks Octopus Electronic Bricks series. It uses a cadmium-sulfide (CdS) photocell that changes resistance based on ambient light levels — the brighter the light, the lower the resistance. With its 3-pin co...

SKU: AF-5708

The Adafruit CAN Pal is a CAN bus transceiver breakout for microcontrollers that have a native CAN peripheral. It converts 3.3V logic-level CAN TX/RX signals to the differential signalling required for the CAN bus. This is a transceiver only — it does not include a CAN controller, so your microco...

SKU: DF-DFR0406

INTRODUCTION The Arduino Motor Shield is based on L298 (a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors). It helps you drive two DC motors with Arduino board as well as control the speed and direction of the ...

SKU: DF-SEN0213

The DFRobot Gravity Heart Rate Monitor Sensor measures the electrical activity of the heart and outputs it as an analog signal. Built around the AD8232 chip, it filters and amplifies the ECG signal to produce a clean waveform from the PR and QT intervals — viewable in real time using the Arduino ...

SKU: AF-2927

A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). Using our Feather Stacking Headers or Feather Fem...

SKU: AF-6194 · MPN: ADA6194

A warm-white LED filament shaped as the letter "D", made from COB (chip on board) LEDs — the same technology found in Edison-style LED bulbs. Dozens of micro LED diodes are bonded onto a thin metal backing and coated in silicone, producing a bright, uniform glow from both sides. Lightweight and ...

SKU: AF-6196 · MPN: ADA6196

A warm-white LED filament shaped as the letter "F", made from COB (chip on board) LEDs — the same technology found in Edison-style LED bulbs. Dozens of micro LED diodes are bonded onto a thin metal backing and coated in silicone, producing a bright, uniform glow from both sides. Lightweight and ...