All Products

SKU: DF-DFR1103 · MPN: DFR1103

##Introduction The Gravity GNSS Positioning & Timing Module integrates satellite positioning functionality and a real-time clock (RTC). The module automatically obtains satellite time based on a preset calibration period and accurately calibrates the onboard RTC chip. This calibration effectively...

SKU: EC-WRF11010R

A low-cost sub-1 GHz RF transceiver module based on the Texas Instruments CC1101 IC, designed for low-power wireless communication. Pre-configured for 433 MHz operation, it is well suited for ISM and Short Range Device (SRD) applications with a transmission range of 300–500 metres depending on en...

SKU: SF-GPS-19166

The GP-1818MK is a low-cost - high performance GPS module with built in antenna. It can provide position, velocity, and accurate timing through the standard NMEA-0183 protocol. Being low power and compact in design, the GP-1818MK is perfect for basic tracking and positioning, especially with resp...

SKU: DF-TEL0117

LoRa MESH Radio Module is a high performance, low power, long-range micro-power RF module, using a distributed ad-hoc network communication mode, embedded wireless MESH MANET protocols, users do not need to do anything modified to present devices, protocols, nor need for secondary development...

SKU: SF-GPS-29061 · MPN: GPS-29061

Add modular GNSS positioning to a Raspberry Pi or similar single-board computer with this compact SparkPNT GNSS Flex receiver module. It is built around the u-blox DAN-F10N and is designed for reliable metre-level positioning, including challenging urban environments.The module fits the SparkPNT ...

SKU: DF-DFR0571

This is a DC-DC buck-mode power module, with input voltage range 8V~28V and fixed output voltage/current 5V/3A. Its work frequency can reach to 0.5MHz. The module has high conversion rate and small size, easy to embed.Besides, it has steady output voltage, which can work long time without voltage...

SKU: DF-TEL0119

The USB/TTL Raspberry Pi GPS Tracker is a compact GPS location module built around the L80-39 chip. With 66 search channels and 22 simultaneous tracking channels, it delivers fast satellite acquisition and reliable positioning accuracy down to 2.5m. Featuring both USB and TTL interfaces, this mo...

SKU: DF-TEL0138

This is an Ublox chip-based GPS receiver module of low power and high sensitivity that can receive 56 channels satellite signal. Compared with traditional GPS receivers, it brings much more accurate and faster-positioning performance with stronger signals. Integrated with a built-in receiving ant...

SKU: SF-GPS-19663

With GNSS you are able to know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GNSS Real Time Kinematics (RTK) has mastered dialing in the accuracy of their GNSS modules to just millimeters. The SparkFun M...

SKU: DF-TEL0137

This GPS receiver brings much more accurate and faster positioning performance with stronger signal compared with traditional GPS receivers. It is compact, lightweight and portable. Integrated with built-in receiving antenna, this product adopts a high-precision positioning chip and industrial-...

SKU: DF-DFR1179 · MPN: DFR1179

The ZL9NSQ is a high-performance 3D attitude sensor module that integrates a three-axis accelerometer, a three-axis gyroscope, and a three-axis magnetometer. Featuring a 32-bit ARM Cortex-M4F microprocessor, it utilizes the IMU Motion Engine algorithm along with a 2.4G wireless transceiver and pa...

SKU: DF-DFR0051

The Analog Voltage Divider V2 can detect the supply voltage from 0.0245V to 25V. This module is based on resistor divider principle. The voltage detection module allows the input voltage to reduce 5 times. As the Arduino analog input voltage is normally maximum 5V, the input voltage of analog ...

SKU: DF-DFR0559-1

Note: Includes Solar Power Manager 5V and Semi Flexible Monocrystalline Solar Panel (5V 1A). The DFRobot Solar Power Manager series are designed for IoT projects and renewable energy projects, providing safe and high-efficiency embedded solar power management modules for makers and application...

SKU: SF-SPX-18621

An intelligent power board for the smôl ecosystem that boosts the voltage from one or two AAA or AA cells up to 3.3V. Features a TPS61200 boost regulator and an ATtiny43U microcontroller that enables deep sleep for the entire smôl stack — drawing just 12 µA in sleep mode. The processor board can...

SKU: AF-6038 · MPN: ADA6038

The Adafruit SPI Flash SD Card breakout features an XTSD 2 GB chip — an SD card in an SMT package that you can wire up like standard SPI flash but use with existing SD card libraries. It comes pre-formatted as a 2 GB FAT volume and works straight away with the built-in SD library in Arduino or th...

SKU: SF-WRL-15131

After years of popularity with the XBee Series 1 and XBee Series 2 Pro Modules, we now have the XBee Series 3 Pro which brings the best of both worlds. XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols and you can now talk to the modules over UART or SPI as well. With a 300ft i...

SKU: SF-PRT-17257

This is a 500mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. The cable insulation is made from silicon making it more flexible than our original Qwiic cable particularly in tig...

SKU: LB-OWL-SENSOR

Build your electronics projects easier than ever with the use of this sensor shield expansion board. It makes connecting many input devices and output devices to the correct Arduino pins. This great board definitely comes in great quality and at an amazing price. A must-have for your electroni...

SKU: DF-DFR1015

Multiple-output DC–DC converters are essential in a multitude of applications where different DC output voltages are required.This DC-DC step-down voltage power module converts 7.5V~30V input to an output of 3.3V/5V/9V/12V (default to 5V), which can be selected by short-circuiting the correspondi...

SKU: AF-5400

The Adafruit ESP32 Feather V2 is a major redesign of the original HUZZAH32 ESP32 Feather, featuring 8 MB flash, 2 MB PSRAM, USB-C, a STEMMA QT port, a NeoPixel, and a user button. The dual-core ESP32 at 240 MHz provides Wi-Fi and Bluetooth Classic/LE connectivity for wireless and IoT projects. D...