All Products
Showing 21-40 of 43 products · 26 unavailable products hidden
Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max
·
The Adafruit DRV8871 is a single-channel brushed DC motor driver breakout capable of delivering up to 3.6 A peak current with a wide 6.5–45V motor voltage range. Its resistor-set current limiting and built-in PWM support make it straightforward to use with virtually any brushed DC motor. The boa...
Adafruit I2S 3W Class D Amplifier Breakout - MAX98357A
·
The Adafruit MAX98357A I2S Class D Amplifier Breakout is an all-in-one digital audio solution that decodes I2S audio and amplifies it directly to a speaker — no separate DAC required. Delivering up to 3.2W into a 4Ω speaker, it's a compact and efficient way to add amplified sound to your Raspberr...
Adafruit Mini Relay FeatherWing - Latching
·
The Adafruit Latching Mini Relay FeatherWing lets you control mains-powered devices and small appliances using any Feather microcontroller. Switch lamps, fans, solenoids, and other loads rated up to 250 VAC or DC — all from a compact FeatherWing form factor. This is the latching version, which u...
8-Channel PWM or Servo FeatherWing Add-on For All Feather Boards
·
The 8-Channel PWM or Servo FeatherWing adds 8 channels of 12-bit PWM output to any Adafruit Feather board via I2C. It uses an onboard PWM driver with a built-in clock, so it runs independently without tying up your microcontroller — unlike the TLC5940 family, no continuous signal is needed. The ...
Infrared Sensor Jumper Wire - 3-Pin JST
Three pin JST connector with red, black, and yellow colors. 5 inch wire outs. This cable comes fully assembled as shown and connects directly to many different Sharp sensors. Quick and easy, this cable will save you 15-20 minutes over making your own wiring harness. If you need this cable and ...
Adafruit DC Stepper Motor HAT for Raspberry Pi - Mini Kit
·
The Adafruit DC & Stepper Motor HAT drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET motor...
Thermocouple Amplifier with 1-Wire Breakout Board - MAX31850K
·
The MAX31850K breakout board is a 1-Wire thermocouple amplifier with cold-junction compensation for K-type thermocouples. Unlike SPI-based amplifiers, the 1-Wire interface allows any number of thermocouple breakouts to share a single data line — ideal for multi-point temperature measurement. The...
Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016
·
A mini class D with AGC and I2C control? Yes please! This incredibly small stereo amplifier is surprisingly powerful. It is able to deliver 2 x 2.8W channels into 4 ohm impedance speakers (@ 10% THD) and it has a i2c control interface as well as an AGC (automatic gain control) system to keep your...
OLED Breakout Board - 16-bit Color 1.27 w/microSD holder
·
We love our black and white monochrome displays but we also like to dabble with some color now and then. Our 1.27" color OLED displays are perfect when you need a small display with vivid, high-contrast 16-bit color. The visible portion of the OLED measures 1.27" diagonal and contains 128x96 RGB ...
Stereo 2.1W Class D Audio Amplifier - TPA2012
·
This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 2.1W channels into 4 ohm impedance speakers (@ 10% THD). Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, it's incredibly efficient (89% efficient when...
SparkFun Qwiic Cable Kit
The SparkFun Qwiic Connect System is constantly growing in popularity with makers. So to make it even easier to get started, we’ve assembled this Qwiic Cable Kit for everyone. If you aren’t sure which Qwiic cable to use, this handy box includes all of them allowing you to save a little money and ...
Adafruit 16-Channel 12-bit PWM/Servo Shield - I2C interface
·
The Adafruit 16-Channel PWM/Servo Shield brings PCA9685-based servo and PWM control to any Arduino in a convenient shield format. Using only I2C (SCL and SDA), the shield provides 16 channels of 12-bit PWM output with a built-in clock — no continuous signal from your microcontroller needed. Up t...
OLED Breakout Board - 16-bit Color 0.96 w/microSD holder
·
We love our black and white monochrome displays but we also like to dabble with some color now and then. Our new 0.96" color OLED displays are perfect when you need an ultra-small display with vivid, high-contrast 16-bit color. The visible portion of the OLED measures 0.96" diagonal and contains ...
Stereo 3.7W Class D Audio Amplifier - MAX98306
·
This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, its incredibly efficient (over 90% efficient when driving...
STEMMA Wired Tactile Push-Button Pack - 5 Color Pack
·
Little clicky switches are standard input "buttons" on electronic projects. These are just like our Colorful Round Tactile Button Switch Assortment, but already assembled onto a PCB - they even have a pull-up resistor installed! The pins are normally open (disconnected) and when the button is pre...
Adafruit 2.13 Monochrome E-Ink Bonnet for Raspberry Pi - THINK INK
·
The Adafruit 2.13" Monochrome E-Ink Bonnet brings crisp, paper-like displays to your Raspberry Pi with no soldering required. Simply plug this pre-assembled bonnet onto any Pi with a 2×20 header and start displaying high-contrast black-and-white graphics that remain visible even with power discon...
Adafruit 2.13 HD Tri-Color eInk / ePaper Display FeatherWing - 250x122 RW Panel with SSD1680
·
The Adafruit 2.13" HD Tri-Colour eInk FeatherWing brings electronic paper technology directly to your Feather board. Featuring a 250×122 pixel display with black, red, and white ink, this FeatherWing delivers high-contrast, daylight-readable visuals that persist even when power is completely disc...
Adafruit 2.13 250x122 Tri-Color eInk / ePaper Display with SRAM - SSD1680 Driver
·
The Adafruit 2.13" Tri-Colour eInk Display brings electronic paper technology to your microcontroller projects. Featuring a 250×122 pixel display with black, red, and white ink, this breakout delivers high-contrast, daylight-readable visuals that persist even when power is completely disconnected...
Multi-color Block Building Breadboard Kit
This kit includes two kinds of mini multi-color block building breadboards and 2 base plates of different sizes. Users can freely assemble these breadboards to make various projects combining with other microcontrollers like Arduino, Raspberry Pi, etc., or use them in circuit assembly and test in...
Adafruit Infrared IR Remote Transceiver - STEMMA JST PH 2mm
·
The Adafruit Infrared IR Remote Transceiver combines a high-powered IR transmitter and a sensitive 38 kHz IR receiver on a single board. With two 940 nm IR LEDs (one vertical, one horizontal) driven by an onboard N-channel FET at 100–200 mA per LED, you get 10+ metres of transmit range alongside ...
