All Products

SKU: DF-SEN0568

Fermion: MEMS Hydrogen Sulfide H2S Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat generation, short preheating time, and swift response recovery....

SKU: DF-SEN0563

Fermion: MEMS Formaldehyde HCHO Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat generation, short preheating time, and swift response recovery. Th...

SKU: AF-4330

Here is the perfect kit for mounting convex lenses (glass or plastic) to your Monster M4sk! These acrylics has been laser-cut specifically for lenses with a lip-edge, so we can't guarantee it'll fit with any ol' convex lens. But it does work great with ours. And of course, the mounting hardware i...

SKU: DF-SEN0565

Fermion: MEMS Methane CH4 Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat generation, short preheating time, and swift response recovery. The sens...

SKU: AF-1285

The Adafruit Beginner LED Sewing Kit has everything you need to start stitching glowing circuits with conductive thread. No soldering or microcontroller required — the included candle-flicker LEDs twinkle automatically for a warm, animated glow. With enough supplies for two projects with two LED...

SKU: DF-SEN0574

Fermion: MEMS Nitrogen Dioxide NO2 Gas Detection Sensor employs state-of-the-art micro-electromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat generation, short preheating time, and swift response recovery....

SKU: AF-653

This sewable CR2032 battery holder makes it easy to add power to wearable electronics projects. Two small 1mm holes in the metal connection tabs are perfectly sized for a #5 or smaller needle to pass through, so you can stitch it directly onto fabric with conductive thread. One tab connects to g...

SKU: DF-FIT0872

A gold-plated IPEX (U.FL) to SMA male (inner needle) pigtail cable for connecting wireless modules to external antennas. The gold-plated connectors have passed 48-hour salt spray testing for long-lasting corrosion resistance. Built with RG1.13 wire and a high-density shielding layer, this cable ...

SKU: AF-3444

The Adafruit DotStar High Density 8×8 Grid packs 64 individually addressable RGB LEDs into a compact 25.4 mm × 25.4 mm (1" × 1") square. Each DotStar pixel features a built-in PWM driver and is controlled via a 2-wire SPI interface using just two digital I/O pins — data and clock. Each LED deliv...

SKU: SF-TOL-09317

This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don’t normally need a third hand. It’s nice, but soldering flat on a table works just fine. Then again, the desk is starting to loo...

SKU: PL-1013 · MPN: 1013

This connector is a single-row, 3-pin, straight female header strip designed to match 0.1" male headers. The order quantity must be a multiple of five.

SKU: LB-LS0784

Multi-function&nbsp;Silicone Heat Insulation Mat Features circuit board location A&nbsp;screw location 3 parts compartments with cover A magnetic tools area 3 magnetic parts areas 7 non-magnetic parts areas A scale ruler 42 spare cells Screw Location with 124 tiny cells Resistance to high temp...

SKU: AF-1728

A charming sew-your-own owl craft kit by Cynthia Treen Studio. Designed for beginner adults and competent young stitchers, the kit includes all materials and step-by-step instructions to create a small stuffed owl approximately 3.5" (9 cm) tall. Cynthia Treen Studio uses locally sourced and recy...

SKU: WS-19297 · MPN: 19297

This 5G omni-directional antenna provides 18dBi gain across a wide 600–6000MHz frequency range, covering 5G, 4G, 3G, and GNSS bands. The omni-directional radiation pattern delivers consistent signal quality in all directions without needing to orient the antenna toward a specific tower. It conne...

SKU: DF-SEN0566

Fermion: MEMS Volatile Organic Compounds VOC Gas Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat generation, short preheating time, and swift response recovery. ...

SKU: JU-JU-W-LP334 · MPN: JU-W-LP334

You tried to follow the pattern. You really did.&nbsp;This pin is for anyone who’s ever cut the wrong size, lost their last needle, or discovered that yes, glue absolutely does dry faster when it shouldn't.&nbsp;Perfect for makers with a mouth and a sense of humour.&nbsp;This colourful, gold-back...

SKU: AF-2424

This stepper motor is a little different than the large NEMA-17 types you may be used to. These are often used in gauges for motorcycles and cars to replace the old-style fully-analog type. They have extremely fine step precision of about 1/2 a degree per step, 600 steps for single stepping, f...

SKU: AF-2324

The Adafruit Ultimate GPS HAT adds high-quality GPS and GLONASS positioning to your Raspberry Pi. Built around a PA1616D module, it provides precise location data and a built-in real-time clock (RTC) with coin cell backup — perfect for outdoor projects, time synchronisation, and location-aware ap...

SKU: DF-SEN0571

Fermion: MEMS Odor Smell Gas Detection Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA), minimal heat generation, short preheating time, and swift response recovery. The sensor...

SKU: AF-4468

This miniature 5 V cooling fan keeps small computers, FPGAs, motor drivers, and other heat-generating components cool. It features a Molex PicoBlade 1.25 mm pitch 2-pin connector for easy plug-in attachment to compatible board headers, or you can cut the connector off and solder or clamp the wire...