All Products

SKU: DF-DFR0067

This Gravity-compatible DHT11 sensor provides calibrated digital temperature and humidity readings via a single data pin. With an integrated 8-bit microcontroller and factory-calibrated coefficients stored in OTP memory, it delivers reliable measurements with minimal setup. The Gravity 3-pin int...

SKU: DF-DFR0645-G

The Gravity 4-Digital LED Segment Display Module features a bright green 7-segment display with four digits, perfect for showing numbers, time, sensor readings, and other data in your projects. It communicates over I2C for simple two-wire connectivity with Arduino, Raspberry Pi, and other microco...

SKU: DF-SEN0244

The Gravity Analog TDS Sensor is an Arduino-compatible kit for measuring Total Dissolved Solids (TDS) in water. TDS indicates how many milligrams of soluble solids are dissolved per litre — the higher the value, the less clean the water. This sensor outputs a 0–2.3V analog signal that can be read...

SKU: DF-SEN0193

The Gravity Analogue Capacitive Soil Moisture Sensor measures soil moisture using capacitive sensing rather than resistive probes, providing significantly better corrosion resistance and longer service life. Made from corrosion-resistant material for reliable long-term use in soil. An onboard vo...

SKU: DF-SEN0321

The Gravity IIC Ozone Sensor measures ozone (O₃) concentration from 0 to 10 ppm with 10 ppb resolution using an electrochemical sensing element. Factory-calibrated for accurate readings out of the box, it connects via I2C through DFRobot's Gravity 4-pin interface. Compatible with Arduino, ESP32,...

SKU: DF-DFR0979

The Gravity CH423 I2C 24 Digital IO Expansion Module extends your microcontroller with 24 additional digital output/input pins over a standard I2C connection. Based on the CH423 chip, it provides 8 GPIOs with interrupt support and 16 dedicated GPOs. The built-in current drive circuit delivers up...

SKU: DF-SEN0411

The Gravity: LIS331HH is a high-performance 3-axis linear accelerometer with ultra-low power consumption of just 10 µA in low-power mode. It offers user-selectable measurement ranges of ±6g, ±12g, or ±24g and delivers 16-bit data output with configurable data rates from 0.5 Hz to 1 kHz. Using th...

SKU: DF-DFR0076

This Gravity analog flame sensor detects fire and infrared light sources in the 760–1,100 nm wavelength range. With a 60° detection angle and analogue output proportional to flame distance, it's widely used in firefighting robots, fire alarm projects, and other safety applications. The Gravity i...

SKU: DF-DFR0553

DFRobot I2C ADS1115 16-bit ADC module can accurately collect and convert analog signals. Through this ADC module, Raspberry Pi can easily use a wide range of Gravity series analog sensors to measure various signals, and perceive this world.Raspberry Pi is a common master control board which is...

SKU: DF-DFR0300

The Gravity EC (Electrical Conductivity) Sensor measures the conductivity of aqueous solutions, providing an analogue output for Arduino and compatible microcontrollers. EC measurement is essential for monitoring water quality, nutrient levels in hydroponic systems, and soil salinity in agricultu...

SKU: DF-SEN0214

The Gravity Analog 20A Current Sensor measures both AC and DC current using the Hall effect, outputting a proportional analog voltage to your microcontroller. With high-voltage isolation built into the circuit design and a non-conductive acrylic base plate, it's designed for safe use in automatio...

SKU: DF-DFR0577

The Gravity I/O Expansion Shield for Pyboard connects your Pyboard v1.1 to the DFRobot Gravity sensor and module ecosystem with colour-coded plug-and-play connectors. No soldering is required — simply plug Gravity-compatible sensors and modules into the clearly labelled ports. An onboard externa...

SKU: DF-SEN0496

This full-scale oxygen sensor uses an original AO2 CiTiceL electrochemical probe to measure oxygen concentrations from 0–100%Vol via I2C digital output. A built-in calibration algorithm on the signal board supports single-point or double-point calibration for accurate readings in demanding enviro...

SKU: DF-SEN0245

The VL53L0X laser range finder is a high-precision distance sensor that based on new Time-of-Flight (ToF) principle. VL53L0X provides accurate distance measurement whatever the target reflection unlike traditional technology. It can measure absolute distances up to 2m.DFRobot has introduced VL...

SKU: DF-SEN0224

DFRobot presents the ultra low-power Arduino triple axis accelerometer! This device is based around a MEMS LIS2DH chip solution and has high-performance ultra-low power mode. The module is fitted with a Gravity I2C interface for easy plug and play integration in to your projects. The build in...

SKU: DF-SEN0098-V2 · MPN: SEN0098-V2

##Introduction This is an updated version. Retired Product: Gravity: Analog 50A Current Sensor (AC/DC) V1Get this low-power current sensor to monitor your project every second for saving energy or protecting the circuit!This fully integrated Hall Effect-based linear STK-600/M current sensor gives...

SKU: DF-TEL0180 · MPN: TEL0180

The Gravity: WiFi IoT Module is a companion accessory for the Gravity: Science Data Acquisition (SCI DAQ) Module, enabling wireless sensor data transmission to IoT platforms without any programming required. Simply connect sensors to the SCI DAQ module and start uploading data instantly. Operati...

SKU: DF-SEN0501

This multifunctional environmental sensor comprises SHTC3 temperature & humidity sensor, BMP280 barometric pressure sensor, VEML7700 ambient light sensor, and ML8511 UV sensor into one and offers 5 kinds of environmental parameters.Professional sensor chips are selected for each kind of parameter...

SKU: DF-SEN0127

  INTRODUCTION This is a generic Arduino gas sensor. It has MQ2 probe which is able to detect LPG, i-butane, propane, methane ,alcohol, Hydrogen, smoke.It can be used in gas leakage detecting device in consumer and industry markets. It has a high sensitivity and fast response time. ...

SKU: DF-FIT0511

The Gravity 4Pin Sensor Adapter converts 4-pin sensors to the DFRobot Gravity interface, making it easy to connect compatible sensors to Gravity-enabled controllers. Features a press-type terminal for quick, tool-free wire connections. A 3.3V/5V power switch provides flexibility for different se...