All Products

SKU: AF-3444 · MPN: 3444

The Adafruit DotStar High Density 8×8 Grid packs 64 individually addressable RGB LEDs into a compact 25.4 mm × 25.4 mm (1" × 1") square. Each DotStar pixel features a built-in PWM driver and is controlled via a 2-wire SPI interface using just two digital I/O pins — data and clock. Each LED deliv...

SKU: AF-3501 · MPN: 3501

The Adafruit GEMMA M0 is a tiny, coin-sized microcontroller board designed for wearable electronics and small projects. Despite its quarter-sized footprint, it packs serious power with an ATSAMD21E18 32-bit Cortex M0+ processor, 256 KB of Flash, and 32 KB of RAM — a massive upgrade over the origi...

SKU: AF-3800 · MPN: 3800

The Adafruit ItsyBitsy M4 Express is a high-performance microcontroller board powered by the ATSAMD51 Cortex M4 running at 120 MHz with hardware floating point and DSP support. Packed into a tiny 1.4" × 0.7" form factor, it delivers 512 KB Flash, 192 KB RAM, and 2 MB of SPI Flash for CircuitPytho...

SKU: AF-4481 · MPN: 4481

The Adafruit ItsyBitsy nRF52840 Express brings Bluetooth Low Energy connectivity to the tiny ItsyBitsy form factor. Powered by the Nordic nRF52840 Cortex M4 at 64 MHz with 1 MB Flash, 256 KB RAM, and 2 MB QSPI Flash, it can act as both a BLE central and peripheral device — perfect for compact wir...

SKU: AF-1902 · MPN: 1902

The SmartLED Shield (V4) provides a simple, solder-free way to connect a Teensy 3.2, Teensy 3.5, or Teensy 3.6 to HUB75 RGB LED Matrix Panels. Just plug in your Teensy, connect your panel, and start displaying graphics, patterns, or animated GIFs using the SmartMatrix Library. The shield include...

SKU: AF-5201 · MPN: 5201

The Adafruit IS31FL3741 RGB LED Matrix features 117 individually addressable RGB LEDs arranged in a 13×9 grid with 3 mm pitch spacing. Each 2×2 mm LED is driven by the ISSI IS31FL3741 controller chip over I2C, providing 8-bit PWM per colour channel for full 24-bit colour across the entire display...

SKU: AF-6358 · MPN: ADA6358

Build large, colourful HUB75 RGB LED matrix displays from a Raspberry Pi without the usual jumper-wire tangle. This Adafruit Bonnet plugs onto the 40-pin GPIO header and drives three parallel matrix strings using the active3 pinout, so it can handle roughly three times as many panels or pixels as...

SKU: AF-2242 · MPN: 2242

The Adafruit DotStar Digital LED Strip (144 LED/m, white flex PCB) delivers superior performance over traditional NeoPixels with its 2-wire SPI interface. Push data at up to 32 MHz clock speed with no critical timing requirements, making it compatible with virtually any microcontroller or micropr...

SKU: AF-1507 · MPN: 1507

An ultra-high-density NeoPixel strip packed with 144 individually addressable RGB LEDs per metre on a flexible white PCB with white mask. Each pixel offers full 24-bit colour control, and only a single data pin is needed to drive the entire strip. Also available with a black PCB. The strip comes...

SKU: AF-1506 · MPN: 1506

An ultra-high-density NeoPixel strip packed with 144 individually addressable RGB LEDs per metre on a flexible black PCB with black mask. Each pixel offers full 24-bit colour control, and only a single data pin is needed to drive the entire strip. The strip comes in a 1-metre length with weather...

SKU: AF-2328 · MPN: 2328

Adafruit DotStar LED strips use 2-wire SPI instead of the single-wire protocol used by NeoPixels, allowing much faster data rates (up to 32 MHz) and a 20 KHz PWM refresh rate. This makes DotStars ideal for persistence-of-vision (POV) projects and smooth, flicker-free animations — especially at lo...

SKU: AF-3727 · MPN: 3727

The Adafruit ItsyBitsy M0 Express is a compact yet powerful microcontroller board built on the ATSAMD21 Cortex M0+ running at 48 MHz. At just 1.4" × 0.7", it delivers the same capability as the Metro M0 or Feather M0 Express in a fraction of the size — perfect for shrinking prototypes into final ...

SKU: AF-1004 · MPN: 1004

These ingenious little clips make it easier than ever to use our analog RGB LED strips - no need to solder! The clips snap onto the ends of the LED strip and hold securely. They're not waterproof but you could cover them in heat-shrink to make them weatherproof.You get one piece of three differen...

SKU: AF-2241 · MPN: 2241

Adafruit DotStar LED strips use 2-wire SPI instead of the single-wire protocol used by NeoPixels, allowing much faster data rates (up to 32 MHz) and a 20 KHz PWM refresh rate. This makes DotStars ideal for persistence-of-vision (POV) projects and smooth, flicker-free animations — especially at lo...

SKU: AF-2240 · MPN: 2240

The Adafruit DotStar Digital LED Strip (60 LED/m, white flex PCB) delivers superior performance over traditional NeoPixels with its 2-wire SPI interface. Push data at up to 32 MHz clock speed with no critical timing requirements, making it compatible with virtually any microcontroller or micropro...

SKU: AF-2238 · MPN: 2238

The Adafruit DotStar Digital LED Strip (30 LED/m, white flex PCB) delivers superior performance over traditional NeoPixels with its 2-wire SPI interface. Push data at up to 32 MHz clock speed with no critical timing requirements, making it compatible with virtually any microcontroller or micropro...

SKU: AF-2237 · MPN: 2237

The Adafruit DotStar Digital LED Strip (30 LED/m, black flex PCB) delivers superior performance over traditional NeoPixels with its 2-wire SPI interface. Push data at up to 32 MHz clock speed with no critical timing requirements, making it compatible with virtually any microcontroller or micropro...