All Products

SKU: SF-COM-08635

Small electret microphone. Useful in acoustic and audio applications. Documents: Datasheet Example Audio LED control project by Adam Greig

SKU: AF-1063

A well-designed electret microphone amplifier breakout built around the Maxim MAX4466 op-amp, specifically engineered for microphone amplification with excellent power supply noise rejection. The board comes fully assembled and tested with a 20–20 kHz electret microphone soldered on. A trimmer p...

SKU: AF-1713

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret micro...

SKU: DF-FIT0797

Do you worried that your CPU is running too hot? Take a look here! This kind of semiconductor refrigeration module is a simple application of the Peltier Thermoelectric Effect. When the current flows through different interfaces of two conductors, it can absorb and release heat at both ends of th...

SKU: DF-FIT0826

Still worried that your CPU is running too hot? Take a look here! This kind of semiconductor refrigeration module is a simple application of the Peltier Thermoelectric Effect. When the current flows through different interfaces of two conductors, it can absorb and release heat at both ends of the...

SKU: AF-4308

A flexible electric heating pad made from stainless steel fibre fabric. Apply 5–12V DC and it warms up — temperature varies with voltage. Lightweight and flexible enough to wrap around objects or integrate into wearable projects. Essentially a large flexible resistor, it can be driven with PWM v...

SKU: DF-FIT0620

A 12V DC electric solenoid lock with a steel case and steel casting parts. Apply power to retract the latch and unlock; remove power and the latch springs back to the locked position. The lock includes signal feedback output so you can monitor its state from a microcontroller. Built with a pure ...

SKU: KI-2726

Ultra-slim sewable LED boards from Kitronik in sakura lilac, designed for e-textile and wearable electronics projects. Each LED board runs from a 3V coin cell battery and illuminates continuously when powered. The double-sided PCBs feature clearly marked + and – connections for reliable conductiv...

SKU: KI-2746

When using through hole LEDs it can be hard to form the eyelets and then work out which leg is positive and negative. That's where these Sewable LED Holders come in! The 5mm LED holder boards, quickly and easily take any through hole 5mm LED and (after soldering in place) make them easy to use in...

SKU: KI-2762

Add an individually addressable full colour LED to your E-Textiles projects with the Kitronik Sewable ZIP LED. This new addition to our Electro Fashion range incorporates a full colour addressable ZIP LED, which can be controlled by a suitable processor such as the micro:bit. The four connecti...

SKU: AF-623

This electroluminescent (EL) panel produces a smooth, even glow across its entire 10 cm × 10 cm surface. The aqua (blue-green) colour is the natural EL colour and the brightest option available. The panel is flexible, lightweight, and coated in a weather-resistant PVC covering. The panel can be ...

SKU: AF-624

EL panel is the big sister to EL wire - it has the same glow effect but with a flat shape instead of a round shape. This is a big sheet of flexible plastic coated with EL material so its like one big glowing square. It emits an even glow over the entire shape. The glowing part of the panel is ...

SKU: AF-627

A complete starter pack for your first electroluminescent (EL) panel project. Includes a 10 × 10 cm aqua EL panel, a portable battery-powered inverter, and batteries — everything needed to get glowing straight out of the box. The 4×AAA inverter is powerful enough to drive the included panel for ...

SKU: AF-628

A complete starter pack for getting into electroluminescent (EL) panels. Includes a 10 × 10 cm white EL panel, a portable battery-powered inverter, and AAA batteries — everything you need to start glowing right out of the box. The 4×AAA inverter drives a single panel and provides approximately 1...

SKU: AF-632

A complete starter pack for electroluminescent (EL) tape projects, including a 1 m aqua EL tape strip, a portable battery-powered inverter, and batteries. Everything needed to get started with EL lighting right out of the box — no additional components required. Key Features Complete Kit – EL ...

SKU: AF-633

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Blue Portable 4xAAA inverter powerful enough to drive a full meter of s...

SKU: AF-631

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Red Portable 4xAAA inverter powerful enough to drive a full meter of st...

SKU: SF-COM-00096

High-quality radial electrolytic capacitors rated at 100 µF / 25 V. Ideal for power supply decoupling, transient suppression, and smoothing voltage ripple in your projects. Place one between power and ground rails to ensure stable power delivery to sensitive components. Specifications Capacita...

SKU: SF-COM-00523

High-quality radial electrolytic capacitors rated at 10µF / 25V. These low-profile decoupling capacitors are essential components for smoothing power supply noise, suppressing transients, and stabilising voltage in a wide range of circuits. Commonly used as bypass/decoupling caps on power rails,...

SKU: SS-ELB141D1P

This is a Protoshield kit with the same connector as Electronic Brick, you can solder something onto this and use it as a regular Electronic Brick.    You will also need this cable to connect it to Sensor shield. http://www.seeedstudio.com/depot/electronic-brick-fully-buckled-4-...