All Products

SKU: SF-BOB-14021

This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each board features standard B/R/Y/G (Black/Red/Yellow/Green) labels on the top of the ...

SKU: SF-PRT-00132

Through-hole RJ11 socket with PCB mounting posts. 6-pin connection - housing accepts common telephone connectors/wiring. If you need a board for this connector be sure to check out our SparkFun RJ11 Breakout. Two boards are included so be sure to buy two RJ11 connectors to fully utilize them! ...

SKU: SF-PRT-10588

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: SF-BOB-13906

The SparkFun Multiplexer Breakout provides access to all pins and features of the 74HC4051, an 8-channel analog multiplexer/demultiplexer. The 74HC4051 allows you to turn four I/O pins into eight multifunctional, individually selectable signals, which can be used to do everything from driving eig...

SKU: SF-SEN-15335

The SparkFun 9DoF IMU Breakout brings InvenSense's ICM-20948 9-axis motion tracking sensor to a Qwiic-enabled breakout board with an on-board logic level shifter and broken-out GPIO pins. The ICM-20948 is an extremely low-power sensor supporting both I2C and SPI communication, suited for wearable...

SKU: EF-EF05043

The Nezha Breakout Board is a feature-packed expansion board for the micro:bit, designed with classroom use in mind. It integrates 4 servo drivers, 4 motor drivers, and 7 sensor ports — all using RJ11 connectors with foolproof anti-reversal design, so students can plug in confidently without dama...

SKU: SF-BOB-10124

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount o...

SKU: SF-BOB-09966

A simple breakout board for the USB Mini-B connector, bringing all 5 pins out to a breadboard-friendly 0.1" pitch header. Useful for prototyping USB connections or as a convenient 5V power source (up to 100 mA, unregulated). Key Features All 5 Pins Broken Out – VCC, D-, D+, ID, and GND Breadb...

SKU: SF-BOB-11722

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to standard, breadboard friendly, 0.1" headers. Turn it over and it has a footprint for the R/G version! Simply solder an encoder down to the board and you’r...

SKU: SF-BOB-15100

Add a USB-C connector to your project without wrestling with tiny SMD pads. This breakout board routes the USB-C connector's key pins to a standard 0.1" pitch header, making it straightforward to integrate into breadboards and custom PCB designs. Breaks out VBUS, GND, CC1, CC2, D+, and D− — cove...

SKU: SF-BOB-11771

This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA acc...

SKU: SF-BOB-13282

This is a breakout board for the WS2812B RGB LED. The WS2812B is actually an RGB LED with a WS2811 built right into the LED! All the necessary pins are broken out to 0.1" spaced headers for easy bread-boarding. Several of these breakouts can even be chained together to form a display or an addres...

SKU: SF-GPS-21834

The SparkFun SAM-M10Q GPS Breakout features the SAM-M10Q chip-antenna module from u-blox©. The M10Q line is the successor to u-blox's M8Q found on the SparkFun GPS Breakout - Chip Antenna, SAM-M8Q (Qwiic), and is a drop-in replacement with updated features to reduce power consumption by almost ha...

SKU: EF-EF05049

A pack of five RJ11 modular cables with 4P4C (4-position, 4-contact) connectors on each end. Each cable is 200 mm long and provides a four-wire straight-through connection, suitable for connecting sensors and modules that use the RJ11 interface. Key Features 4P4C Connectors – Standard RJ11 plu...

SKU: SF-LCD-15143

The SparkFun TFT LCD Breakout features a 1.8″ colour display with 128 × 160 pixel resolution and a 4-wire SPI interface. A built-in microSD card holder on the same SPI bus provides storage for images and multimedia files while keeping the pin count low. The breakout accepts both 5 V and 3.3 V po...

SKU: SF-SEN-13030

The SparkFun RFID Reader Breakout converts the 2mm pin spacing of ID-series RFID readers to breadboard-friendly 0.1" headers. Compatible with the ID-3LA, ID-12LA, and ID-20LA readers, this board lets you solder the reader directly or use 2mm sockets for a removable connection. Every pin is broke...

SKU: SF-BOB-09322

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>4.9V). When the gate is blocked by a finger, writing utensil, food pellet, or an...

SKU: SF-BOB-13099

The SparkFun Rotary Switch Potentiometer Breakout is a small board the allows you to add resistors to a 10-position rotary switch, turning it into a potentiometer with 10 discrete steps. Multiple applications require potentiometers that are hard to find due to specific resistance values or cus...

SKU: SF-GPS-24114 · MPN: GPS-24114

The SparkFun GNSS L1/L5 Breakout - NEO-F10N, SMA is a standard precision GNSS board with meter-level positional accuracy. The NEO-F10N uses the L1/L5 bands instead of the more commonly seen L1/L2 bands. Utilizing the L5 band, the NEO-F10N delivers improved performance under challenging urban envi...

SKU: SF-SEN-14722

This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long ranges for its size. The VL53L1X uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an Infrared laser to time the ref...