All Products

SKU: SF-DEV-08777

Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient...

SKU: LB-LR-DIGI-TEMP-3M-UA

The Little Bird 1-Wire Digital Temperature Sensor for Raspberry Pi — a plug-and-play solution for environment sensing, data logging, and IoT applications. Simply plug it onto the Raspberry Pi GPIO header — no breadboard, jumper wires, or additional components needed. This is the unassembled vers...

SKU: LB-LR-DIGI-TEMP-3M-A

The Little Bird 1-Wire Digital Temperature Sensor for Raspberry Pi — a plug-and-play solution for environment sensing, data logging, and IoT applications. Simply plug it onto the Raspberry Pi GPIO header — no breadboard, jumper wires, or additional components needed. This is the assembled versio...

SKU: LB-24-TEMP

A pre-wired DS18B20 digital temperature sensor on a breakout module with three labelled pins for easy connection. The DS18B20 uses the 1-Wire protocol, requiring only a single data line to communicate temperature readings to a microcontroller such as a Raspberry Pi, Arduino, or micro:bit. Key Fe...

SKU: SF-SEN-00245

The DS18B20 is a digital temperature sensor from Maxim (now Analog Devices) that communicates over a 1-Wire bus. It reports temperature in degrees Celsius with 9 to 12-bit configurable resolution. Each sensor has a unique 64-bit serial number, allowing multiple sensors to share a single data line...

SKU: SF-SEN-25200 · MPN: SEN-25200

Build a detailed indoor air monitor with this Qwiic combo board, pairing Sensirion’s SCD41 CO2 sensor with the SEN55 environmental sensor node. Together they measure CO2, volatile organic compounds (VOCs), particulate matter across PM1.0, PM2.5, PM4 and PM10, temperature and relative humidity.The...

SKU: SF-SEN-13314

The TMP102 is an easy-to-use digital temperature sensor from Texas Instruments. The TMP102 breakout allows you to easily incorporate the digital temperature sensor into your project. While some temperature sensors use an analog voltage to represent the temperature, the TMP102 uses the I2C bus of ...

SKU: EF-EF04070

The Octopus LM35 Analog Temperature Brick is a plug-and-play temperature sensor module based on the TI LM35D precision centigrade temperature sensor. The LM35 outputs a voltage linearly proportional to temperature (10 mV/°C), making it easy to read with any microcontroller's analog input — no cal...

SKU: AF-165

The TMP36 is a low-power analog temperature sensor that outputs a voltage proportional to ambient temperature. It operates on 2.7–5.5V and requires no external calibration — simply read the analog voltage and convert to temperature. Key Features Analog Voltage Output – Proportional to temperat...

SKU: EC-SEM02001S

Japan's Hokuriku resistive humidity sensor production as a Temperature & Humidity sensor.Application Idea Test and testing equipment; Automatic control; Weather station; Humidity regulator; Features Measure the relative temperature and humidity sensor (humidity range 18% - 98% temperature range -...

SKU: SF-DEV-11262

The ProtoSnap series is a new way to prototype your project without a breadboard. Everything is wired together on a single board, which makes it easy to explore the possibilities of the components before snapping them apart and building them into your project. The ProtoSnap LilyPad Development...

SKU: SF-SEN-11859

This is not your typical temperature sensor. The TMP006 Breakout can measure the temperature of an object without making contact with it. By using a thermopile to detect and absorb the infrared energy an object is emitting, the TMP006 Breakout can determine how hot or cold the object is. The TMP0...

SKU: EF-EF05041 · MPN: EF05041

The PlanetX Waterproof 18B20 Temperature Sensor is a sensor that senses temperature and converts it into a usable output signal. It is waterproof and can be used for temperature measurement. It is usually used for the detection of water temperature. SPECIFICATIONConnections: RJ11 4P4CPower S...

SKU: DF-DFR0645-G

The Gravity 4-Digital LED Segment Display Module features a bright green 7-segment display with four digits, perfect for showing numbers, time, sensor readings, and other data in your projects. It communicates over I2C for simple two-wire connectivity with Arduino, Raspberry Pi, and other microco...

SKU: DF-SER0059

A miniature serial bus servo from DFRobot that delivers 2.3 kg·cm of stall torque at 6 V, controllable via TTL serial communication. Up to 253 servos can be daisy-chained in series, each assigned a unique ID for individual or synchronised control at baud rates up to 1 Mbps. The hybrid gear train...

SKU: SF-DEV-14629

The LilyPad Light Sensor is a sewable breakout board with an ALS-PT19 light sensor built in and ready to use right away. Each sensor outputs voltage between 0V and 3.3V depending on the level of ambient light shining on it. As more light is applied on the sensor, more current will flow from ...

SKU: SF-DEV-14346

The LilyPad ProtoSnap Plus is a sewable electronics prototyping board that you can use to explore circuits and programming, then break apart to make an interactive fabric or wearable project. Programming the ProtoSnap Plus is easy with the free Arduino software you’ll need to program the ATmega32...

SKU: LB-ETEXTILELED-G

This is a simple single unit GREEN E-Textile LEDEach unit can be sewn into fabric. Various input, output, power and sensor boards are available. They’re even washable (with special care)!These are a thicker PCB than the Sparkfun Lilypad LEDs 

SKU: SF-DEV-09267

The LilyPad Accelerometer is a three-axis accelerometer based on the Analog Devices ADXL335, designed for the LilyPad wearable e-textile system. It detects joint movement, inclination, and vibration, outputting 0–3 V analogue signals on the X, Y, and Z axes. The board features large sewable pads...

SKU: LB-ETEXTILELED-B

This is a simple single unit BLUE E-Textile LEDEach unit can be sewn into fabric. Various input, output, power and sensor boards are available. They’re even washable (with special care)!These are a thicker PCB than the Sparkfun Lilypad LEDs