All Products

SKU: AF-1850

Add a touch of sparkle to your wearables with the Adafruit Gemma Sequin Starter Pack. This beginner-friendly kit includes a GEMMA V2 sewable microcontroller, warm white LED sequins, conductive thread, needles, and a coin cell battery holder — everything you need to start sewing glowing electronic...

SKU: AF-5023

A compact Bluetooth-enabled clock and sensor that displays the current time, temperature, and humidity on a crisp e-ink screen. At just 110 × 55 mm with a minimal ABS enclosure, it fits neatly on a desk, shelf, or wall. The sensor broadcasts temperature and humidity data over Bluetooth Low Energ...

SKU: AF-1359

These SMD testing tweezers are a built-in multimeter with tweezer-shaped probes — just grab a component to test it. No more fumbling with bulky multimeter probes on tiny 0402 or 0603 parts. Measure resistors, capacitors, diodes, and LEDs by simply pinching them between the tips. A scanning mode ...

SKU: AF-1871

A sewable breakout board with a CR2032 coin cell battery holder, built-in on/off switch, and 0.1" pitch breakout pins. The board provides two ground pins, one switched power pin, and one always-on power pin — giving you flexibility in how you manage power in your project. Also available: version...

SKU: LB-EAGLED-BUZZ-KIT

The EagLED is Little Bird Electronics' own Arduino-compatible wearable development kit, designed from the ground up for e-textile projects. It packs a microcontroller, LEDs, light sensor, push button, and buzzer onto a snippable board — with snap-off satellite boards for eyes, stars, and hearts t...

SKU: LB-EAGLED-BUZZ

EagLED is Little Bird Electronics' wearable development kit: an Arduino-compatible microcontroller board with LEDs, a light sensor, push button and buzzer built into a snippable PCB for e-textile projects.Built-in USB support lets you program and power the board from a computer. It works with the...

SKU: SF-TOL-10829

This smart SMD tester is essentially a pair of multimeter tweezers. This allows you to troubleshoot circuits with small SMD parts without having to fumble with large probes or long wires. Test resistors, capacitors and diodes one-handed!Features:  Resistance Range: 300Ω/3KΩ/30KΩ/300KΩ ±(1.0%...

SKU: AF-1870

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit to a real-time clock or similar module. Key Features CR2032 Coin Cell Holder ...

SKU: SF-GPS-30975 · MPN: GPS-30975

Built around the u-blox ZED-F9T-20B receiver, this breakout is made for projects where precise time matters as much as location. Under clear skies it can provide five nanoseconds of timing accuracy without requiring external GNSS correction data, making it suitable for 5G IoT networks, distribute...

SKU: SF-DEV-08822

A 20 mm coin cell battery holder designed for CR2032 batteries. The holder features a pop-in, pop-out mechanism for easy battery changes, and the mounting feet include small holes for sewing onto fabric — making it suitable for e-textile and wearable electronics projects as well as standard PCB u...

SKU: AF-653

This sewable CR2032 battery holder makes it easy to add power to wearable electronics projects. Two small 1mm holes in the metal connection tabs are perfectly sized for a #5 or smaller needle to pass through, so you can stitch it directly onto fabric with conductive thread. One tab connects to g...

SKU: DF-DFR0998

This real-time clock (RTC) module uses the SD3031 chip, which has an integrated crystal oscillator and temperature compensator. This provides high-precision timing and stability. At a temperature of 25 °C, the accuracy is maintained at ±3.8ppm (±0.32832 seconds/day).The SD3031 can be powered by b...

SKU: AF-3672

This kit is designed for use with the electronic textiles unit in the Exploring Computer Science (ECS, exploringcs.org) introductory computing curriculum for secondary students. It contains most of the materials needed for four e-textiles projects: paper circuit, wristband, mural, and hum...

SKU: AF-680

These 5mm diffused RGB LEDs feature a built-in controller chip that automatically cycles through colours in a fast flashing pattern — no microcontroller or programming required. With just two leads (power and ground), they're as simple to use as a standard LED. The diffused lens provides an even...

SKU: AF-1657

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a U...

SKU: SF-GPS-26620 · MPN: GPS-26620

Built around the Quectel LG290P, this compact RTK GNSS breakout is designed for high-precision positioning projects that need quad-band, multi-constellation reception. It follows the same board dimensions, pin layout and connectors as SparkFun’s GPS-RTK-SMA Breakout - ZED-F9P (Qwiic), making it a...

SKU: LB-JSTBOARD

This E-textiles board is a breakout for a JST, so you can sew it onto a garment or use it in Paper Circuits! The JST breakout board can be easily sewn through the large holes. For paper circuits, simply apply copper tape on top of it.A wearable lithium polymer battery or wearable lipo also kno...

SKU: SF-GPS-27316 · MPN: GPS-27316

The Quectel LG290P is a compact, high-precision GNSS module for demanding positioning applications. It supports quad-band, multi-constellation reception across GPS, GLONASS, Galileo, BDS, QZSS and NavIC, along with SBAS augmentation systems including WAAS, EGNOS, BDSBAS, MSAS, GAGAN and SDCM.Desi...

SKU: DF-DFR1236 · MPN: DFR1236

This development kit combines the FireBeetle 2 ESP32-C5 microcontroller board with a dedicated solderless IO expansion shield, giving you a practical platform for smart home and IoT prototypes.The ESP32-C5 brings dual-band Wi-Fi 6 on 2.4 GHz and 5 GHz, plus Bluetooth 5, Thread and Zigbee support....

SKU: AF-80

A high-quality 9V battery clip with a pre-assembled 5.5mm/2.1mm centre-positive barrel connector. The moulded plastic clip covers the battery terminals to prevent short circuits, and the barrel plug connects directly to Arduino boards and other devices with a standard DC barrel jack. Key Feature...