All Products

SKU: SF-DEV-13746

The SparkFun Beefy 3 is an FTDI Basic Breakout board based on the FT231X USB-to-serial IC. Unlike standard FTDI breakouts, it features an AP2112K voltage regulator capable of supplying up to 600mA at 3.3V — enough to power a 3.3V project directly from the board's USB connection. The 6-pin header...

SKU: SF-BOB-13263

Introducing the 3.3V SparkFun FT231X Breakout board, complete with the full UART hardware handshake feature! The pin-out of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications.This board still brings o...

SKU: SF-LCD-15143

The SparkFun TFT LCD Breakout features a 1.8″ colour display with 128 × 160 pixel resolution and a 4-wire SPI interface. A built-in microSD card holder on the same SPI bus provides storage for images and multimedia files while keeping the pin count low. The breakout accepts both 5 V and 3.3 V po...

SKU: SF-SEN-15335

The SparkFun 9DoF IMU Breakout brings InvenSense's ICM-20948 9-axis motion tracking sensor to a Qwiic-enabled breakout board with an on-board logic level shifter and broken-out GPIO pins. The ICM-20948 is an extremely low-power sensor supporting both I2C and SPI communication, suited for wearable...

SKU: SF-SEN-19764

A Qwiic-compatible breakout board for the STMicroelectronics ISM330DHCX — a high-performance 3D accelerometer and 3D gyroscope designed for industrial applications. The 1" × 1" board communicates over I2C via the Qwiic connector system, with 0.1"-spaced pins also broken out for soldered connectio...

SKU: SF-SEN-19895

The SparkFun 9DoF IMU Breakout combines the high-performance ISM330DHCX 3D accelerometer and gyroscope from STMicroelectronics with the MMC5983MA triple-axis magnetometer from MEMSIC, delivering nine degrees of freedom on a single Qwiic-enabled board. Using the SparkFun Qwiic Connect System, no ...

SKU: SF-SEN-14844

It’s time to say hip hip array for this IR Breakout! The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating, in essence, a low resolution thermal imaging camera. With this breakout you can detect surface temperatures from many feet away with an accur...

SKU: SF-SEN-14843

It’s time to say hip hip array for this IR Breakout! The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating, in essence, a low resolution thermal imaging camera. With this breakout you can detect surface temperatures from many feet away with an accur...

SKU: SF-SEN-14722

This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long ranges for its size. The VL53L1X uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an Infrared laser to time the ref...

SKU: SF-BOB-09966

A simple breakout board for the USB Mini-B connector, bringing all 5 pins out to a breadboard-friendly 0.1" pitch header. Useful for prototyping USB connections or as a convenient 5V power source (up to 100 mA, unregulated). Key Features All 5 Pins Broken Out – VCC, D-, D+, ID, and GND Breadb...

SKU: SF-BOB-12700

This simple breakout board routes a female USB Type-A connector's VCC, GND, D−, and D+ pins to a standard 0.1″ pitch header. It saves you the hassle of soldering tiny SMD connectors when adding USB host or device connectivity to your project. Key Features Female USB Type-A Connector – Accepts ...

SKU: SF-SEN-13763

A low-cost, highly accurate digital humidity and temperature sensor breakout board based on the Silicon Labs Si7021. Communicates over I²C with just two data lines, providing relative humidity and precise temperature readings for environmental monitoring projects. The breakout includes built-in ...

SKU: SF-WRL-11812

This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and programm...

SKU: SF-SEN-13030

The SparkFun RFID Reader Breakout converts the 2mm pin spacing of ID-series RFID readers to breadboard-friendly 0.1" headers. Compatible with the ID-3LA, ID-12LA, and ID-20LA readers, this board lets you solder the reader directly or use 2mm sockets for a removable connection. Every pin is broke...

SKU: SF-PRT-10588

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: SF-BOB-16446

The SparkFun Qwiic micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. We've already attached headers to this version of the board so you d...

SKU: SF-SEN-14607

Get ready to be able to see like the Predator! The SparkFun Grid-EYE Infrared Array Breakout board is an 8x8 thermopile array, meaning you have a square array of 64 pixels capable of independent temperature detection. It’s like having a thermal camera, just in a lower resolution. To make it ...

SKU: SF-LCD-29467 · MPN: LCD-29467

  The SparkFun Red Vision Touch Display for Pico features a 2.0", 320x240px capacative touch LCD mounted on a breakout board designed to plug directly into the Control Board on the Experiential Robotics Platform (XRP) Kit as well as Raspberry Pi Picos. This display board includ...

SKU: SF-GPS-24114 · MPN: GPS-24114

The SparkFun GNSS L1/L5 Breakout - NEO-F10N, SMA is a standard precision GNSS board with meter-level positional accuracy. The NEO-F10N uses the L1/L5 bands instead of the more commonly seen L1/L2 bands. Utilizing the L5 band, the NEO-F10N delivers improved performance under challenging urban envi...

SKU: SF-BOB-11722

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to standard, breadboard friendly, 0.1" headers. Turn it over and it has a footprint for the R/G version! Simply solder an encoder down to the board and you’r...