All Products

SKU: PI-1SHEELD

The 1Sheeld+ is a Bluetooth shield for Arduino that turns your smartphone into over 40 different Arduino shields. Connect your iPhone or Android device via the free 1Sheeld app, and use your phone's sensors, camera, GPS, social media, and more directly from your Arduino sketch. The shield acts a...

SKU: SF-DEV-18386

The MyoWare® 2.0 Muscle Sensor is designed to be wearable, allowing you to attach biomedical sensor pads directly to the board itself. However, there still may be cases where you want to mount the sensor pads away from the board; this is where the MyoWare 2.0 Cable Shield comes in. The shield inc...

SKU: AF-5349

Protect your RFID-enabled cards from unauthorised scanning with these holographic RFID blocking card sleeves. Each sleeve shields the radio frequency identification (RFID) chip in your credit cards, bank cards, and photo IDs from being read by uninvited RFID readers — far more effective than wrap...

SKU: DF-DFR0256

The Mega Multi IO Expansion Shield lets you stack up to four shields simultaneously on an Arduino Mega or Due without worrying about I/O pin conflicts. All Mega I/O pins are expanded and routed to four separate shield slots, keeping your project clean and tidy with organised cabling. Key Feature...

SKU: DF-DFR0224

The Arduino Screwless Terminal Shield breaks out all Arduino Uno-compatible header pins to spring-loaded push-in terminal blocks. Press the lever, insert your wire, and release — no screwdriver needed. The shield stacks with standard Arduino shields, so you can add additional boards on top. Key ...

SKU: AF-85

“How could something so simple be so useful?”  We heard once that in the 4th millenium B.C. some guy asked the person who invented the wheel that question.  The person who invented the wheel’s answer, we were told, was something like “well it’s not actually that simple - i...

SKU: EC-ACS52001S

The W5200 Ethernet Shield adds wired internet connectivity to your Arduino. Simply stack it onto your board, connect an RJ45 cable, and start communicating over the network. The W5200 controller provides a 32 KB internal buffer — double that of the W5100 — and supports up to eight simultaneous TC...

SKU: EF-EF04015

The Octopus TA12-100 is a non-invasive AC current sensor brick from ElecFreaks. It uses a current transformer to measure AC current flowing through a wire without needing to cut or splice the circuit — simply clamp it around the conductor. The sensor outputs an analogue voltage proportional to th...

SKU: DF-DFR0327

The Gravity Arduino Shield for Raspberry Pi brings Arduino-compatible I/O to your Raspberry Pi B+, 2B, 3B, 3B+, or 4B. Built around the ATmega32u4 (Arduino Leonardo), it sits on top of your Pi and gives you access to all standard Arduino shields and sensors alongside the Pi's own GPIO, I2C, SPI, ...

SKU: AF-1438

The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. Drive up to 4 DC motors or 2 stepper motors plus 2 hobby servos from a single sta...

SKU: DF-DFR0920

The Terminal Block Shield for Arduino replaces loose jumper wires with secure screw-terminal connections, making your wiring stable and reliable. Each Arduino pin is broken out to a 3.5 mm pitch terminal block, and multiple 3.3V, 5V, and GND ports are provided for convenient power distribution. ...

SKU: SF-DEV-16789

The SparkFun Qwiic Shield for Arduino Nano provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Arduino Nano board. The Qwiic shield connects the I2C bus (GND, 3.3V, SDA and SCL) on your Arduino Nano to four SparkFun Qwiic connectors (two horizontally and two ...

SKU: SF-KIT-15716 · MPN: KIT-15716

This passive adapter lets a Teensy development board connect to the standard Arduino 1.0 (R3) shield footprint, making it easier to reuse existing Arduino shields without a breadboard full of jumper wires.Solder your Teensy board, sold separately, to the marked footprint on the adapter, then plug...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...

SKU: EF-EF02037

CAN-BUS is a common industrial bus because of its long travel distance, medium communication speed and high reliability. It is commonly found on modern machine tools and as an automotive diagnostic bus. This CAN-BUS Shield adopts MCP2515 CAN Bus controller with SPI interface and MCP2551 CAN tr...

SKU: DF-FIT0146

An 8-pin female header with extra-long legs, designed for stacking Arduino shields. The extended pins pass through to the board below, allowing multiple shields to be stacked on a single Arduino. Pins are spaced at standard 0.1″ (2.54mm) pitch. Specifications Pin Count – 8 pins, single row Pi...

SKU: SS-103030002

The mbed Shield is an application board designed for the mbed LPC1768 prototyping platform. It brings together CAN, Ethernet, USB, and four standard Grove connectors on a single board, making it easy to connect sensors, actuators, and communication interfaces to your mbed projects. With a standa...

SKU: DF-DFR0272

An Arduino-compatible Ethernet shield based on the Wiznet W5200 chip, providing a simple way to connect your Arduino to a network. It plugs directly onto an Arduino Uno or Mega 2560 and supports stacking additional shields on top. An aluminium alloy heatsink is fitted to the W5200 chip for therma...

SKU: DF-DFR0308

The Arduino DTMF Shield is a dual-tone multi-frequency decoder module that lets your Arduino interpret touch-tone signals from phones. Connect it to a GSM/GPRS shield and you can send commands to your Arduino via phone call — press buttons on your phone to control motors, lights, or any connected...

SKU: SF-PRT-10007

A set of stackable headers designed for the Arduino Uno, Arduino Pro, and other boards using the classic (pre-R3) pin layout. These female headers sit tall enough to clear the USB-B connector, making them ideal for stacking multiple shields. The kit includes two 8-pin and two 6-pin headers — enou...