All Products
Showing 1-20 of 60 products
Little Rubber Bumper Feet - Pack of 4
Small self-adhesive rubber bumper feet for electronics boards and devices. Stick them to the bottom of any PCB to protect your desk, prevent sliding, and provide clearance for through-hole solder joints underneath. The adhesive is strong enough to stay put during normal use but can be removed wi...
Silicone Bumpers - 5x11mm (4 Pack)
Protect your board or project with this four pack of silicone bumpers! Rubber feet raise your PCB or project up off your desk. This helps prevent short circuiting from bits of scrap wire floating about or setting a project down on a conductive surface. They also prevent your enclosure or PCB from...
Adafruit 4x4 Trellis Feather Acrylic Enclosure + Hardware Kit
This laser-cut acrylic enclosure kit turns your 4×4 NeoTrellis setup into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside the NeoTrellis RGB Driver PCB. The enclosure inclu...
Rubber Feet for the Raspberry Pi
·
These handy rubber feet are great for sticking on the bottom of things, and we found that they act as a great base when stuck on the bottom of the Raspberry Pi - no more desk scratches or skating boards! The feet come as a set of 4 in a little square, ready to pop out and use as and when required...
Official Raspberry Pi Foundation Raspberry Pi 4 Case - Red White
The official Raspberry Pi Foundation case for the Raspberry Pi 4 Model B. This solid ABS enclosure in the classic red and white colour scheme keeps your Pi secure while providing labelled cut-outs for all connectors: micro HDMI, USB-C power, Ethernet, USB ports, and the GPIO header. The snap-fit...
Adafruit 8x8 Trellis Feather M4 Acrylic Enclosure + Hardware Kit
This laser-cut acrylic enclosure kit turns your 8×8 NeoTrellis setup (four 4×4 NeoTrellis boards) into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside four NeoTrellis RGB Dr...
Adafruit NeoTrellis M4 with Enclosure and Buttons Kit Pack
Everything you need to get started with the NeoTrellis M4 in one kit. This pack bundles the NeoTrellis M4 Mainboard, an acrylic enclosure, silicone elastomer button pads, and rubber feet — ready to assemble into a complete MIDI controller, sound board, or interactive button-pad device. The NeoTr...
HighPi Pro 5S Case for Raspberry Pi 5
The HighPi Pro 5S Case for Raspberry Pi 5 continues the HighPi case line, offering ease of use, flexible configuration, and attractive design. It embraces the upgrades found on the Pi 5 board, namely its active cooler, power button, and PCIe port. Lots of space is available for HATs, such as powe...
Black Metallic-Look Plastic GH60 / 60% Keyboard Shell
This GH60-compatible 60% keyboard shell is the perfect starting point for a custom mechanical keyboard build. Made from injection-moulded plastic with an eye-catching metallic-glitter finish and styled grooves, it looks great while keeping costs well below milled aluminium alternatives. Designed...
PCB Coaster with Gold Adafruit Logo
This PCB coaster features the Adafruit logo in gold ENIG (Electroless Nickel Immersion Gold) finish on a sturdy 100 × 100 mm FR4 circuit board with black silkscreen. The gold plating resists oxidation, keeping the design looking sharp on your workbench, desk, or coffee table. Four adhesive rubbe...
Silicone Bumpers - Large (10x16.5mm, 4 pack)
Rubber feet raise your PCB or project up off your desk. This helps prevent short circuiting from bits of scrap wire floating about or setting a project down on a conductive surface. They also prevent your enclosure or PCB from sliding around. They can also be used as feet for enclosures. These ar...
Mini-Magnet Feet for RGB LED Matrices (Pack of 4)
A pack of four magnetic mounting feet designed for RGB LED matrix panels. At 16.6 mm long, each magnet-screw slots into the standard 3 mm mounting bosses found on most RGB matrix panels, providing a quick and secure way to display your project on any magnetic surface. Compatible Panels 16×32 RG...
Plastic mounting plate for breadboard and Arduino - rubber feet!
By popular demand! We now have the plates from the ARDX available separately. Acrylic plate is engraved and cut here at the Adafruit factory. There are mounting holes for your Arduino and a space that fits a half sized breadboard very nicely. THIS DOES NOT FIT THE ARDUINO MEGA. Comes with: ...
Adafruit 4x4 NeoTrellis Feather M4 Kit Pack
Build a handheld light-up button controller with this complete kit that pairs the Adafruit 4×4 NeoTrellis RGB Driver with a Feather M4 Express inside an elegant laser-cut acrylic enclosure. The 16 silicone buttons each have individually addressable NeoPixels underneath, and the seesaw I2C chip ha...
Adafruit MacroPad RP2040 Enclosure + Hardware Add-on Pack
Complete the look of your Adafruit MacroPad RP2040 with this enclosure and hardware add-on pack. It includes a decorative bottom plate, a mechanical keyboard stabiliser plate, a rotary encoder knob, mounting screws, and rubber feet — everything you need to give your MacroPad a polished, professio...
Black Anodized Aluminum Bumper Feet - Pack of 2
Sleek black anodized aluminum bumper feet with embedded rubber grips for no-slip support. Originally designed for keyboard enclosures, these machined aluminium feet look great on any electronics project, enclosure, or custom build. Each foot attaches with the included M4-threaded machine screw —...
Purple Anodized Aluminum 60% / GH60 Keyboard Shell
Back in my day, if you wanted a mechanical keyboard, you had to purchase a massive IBM Model M Keyboard but now you can DIY your very own compact keyboards with your very favorite layouts to make the keeb of your dreams.For all the DIY keebfans in the house here is a supe...
Silicone Caps for Digital Addressable Strips - pack of 4
For those that want to cut, customize, and cap our awesome Digital Addressable RGB LED strips we now have a pack of the little rubber caps. These fit perfectly over the strips, use silicone glue to secure and waterproof them.Comes in a pack of 4 pieces
NVMe Base for Raspberry Pi 5
·
Add super-fast NVMe storage to your Raspberry Pi 5 with the Pimoroni NVMe Base. This PCIe extension board mounts underneath your Pi and accepts M-key NVMe SSDs in 2230 to 2280 form factors, delivering lightning-fast boot times and high IOPS for file servers, media centres, and NAS applications. ...
Budget Pack for Raspberry Pi 4 (Doesn't include Raspberry Pi)
Gotta say - this Pi 4 is fly. All the cool kids are going to have it - but all the coolest kids are also going to have a big pack of super cool accessories.We've hand-selected these accessories as the perfect accompaniment to your new Raspberry Pi 4 - Model B. It's everything you need...
