All Products
Showing 1-10 of 10 products
JST PH 3-Pin to Male Header Cable - 200mm
·
The JST PH 3-Pin to Male Header Cable converts a JST PH 3-pin connector into three individual colour-coded wires, each terminated with a 0.1" (2.54 mm) male header pin. It's ideal for extending sensor or LED connections to a breadboard or development board. At 200 mm long, this cable provides en...
STEMMA Wired Tactile Push-Button Pack - 5 Color Pack
·
Little clicky switches are standard input "buttons" on electronic projects. These are just like our Colorful Round Tactile Button Switch Assortment, but already assembled onto a PCB - they even have a pull-up resistor installed! The pins are normally open (disconnected) and when the button is pre...
STEMMA Wired Potentiometer Breakout Board - 10K ohm Linear
·
For the easiest way possible to measure twists, turn to this STEMMA potentiometer breakout (ha!). This plug-n-play pot comes with a JST-PH 2mm connector and a matching JST PH 3-Pin to Male Header Cables - 200mm, so wiring up is a cinch. Simply plug the cable in, then use the black wire to c...
JST PH 3-Pin to Female Socket Cable - 200mm
·
This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" female header sockets on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a ver...
JST SH Compatible 1mm Pitch 3 Pin to Premium Male Headers Cable
If you're fancying to connect to the debug port on a Pico WH, or the two ports on a Pico Debug Probe or anything else with a JST SH compatible 3-pin connector, this cable will do the trick. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch plug connectors on the other. Note that t...
TSSP77038 38kHz IR Demodulator Breakout
·
This breakout uses Vishay's TSSP77038 infrared demodulator to give you the raw demodulated output from a 38kHz IR signal, without the extra filtering used in typical remote-control receivers. That makes it a handy choice for reflective sensing, light barriers, fast proximity detection, and modula...
ScoutMakes DRV5032 Digital Hall Effect Sensor Breakout
·
Add magnetic sensing to your project with this breakout built around the Texas Instruments DRV5032 digital Hall effect sensor. Its digital output changes when the magnetic flux density threshold is crossed, making it useful for detecting magnets, position, lids, doors, rotations and other simple ...
Micro Servo with 3-pin JST Cable - STEMMA Connector Compatible
·
This tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor c...
NeoRGB STEMMA NeoPixel to RGB PWM LED & Strip Driver
·
This handy STEMMA board lets you control 'true analog' LED strips and other PWM-able LEDs from a NeoPixel-compatible data line, without the usual extra wiring of separate driver FETs. A WS2811F handles the 800KHz NeoPixel signal and drives AO3406 N-channel FETs, so a common-anode RGB strip or LED...
1.25mm Pitch 3-pin Cable 20cm long 1:N Cable - Molex PicoBlade Compatible
·
This 1.25 mm pitch 3-pin cable is a compact, Molex PicoBlade-compatible connector cable for projects where standard 0.1″ headers are too bulky. At 20 cm long, it provides a convenient connection length for internal wiring without excess slack. The friction-lock connectors provide a secure, click...
