All Products

SKU: AF-1713 · MPN: 1713

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret micro...

SKU: DF-DFR0498

DFRobot FireBeetle series are low power consumption development modules designed for Internet of Things (IoT). The FireBeetle Covers-Camera & Audio Media Board is a multimedia device for IoT that provides interfaces to connect NAU8822 CODEC IIS, OV7725 camera, SD card (SDIO), earphone and mic...

SKU: AF-1063 · MPN: 1063

A well-designed electret microphone amplifier breakout built around the Maxim MAX4466 op-amp, specifically engineered for microphone amplification with excellent power supply noise rejection. The board comes fully assembled and tested with a 20–20 kHz electret microphone soldered on. A trimmer p...

SKU: AF-4317 · MPN: 4317

Machine learning has come to the 'edge' - small microcontrollers that can run a very miniature version of TensorFlow Lite to do ML computations. But you don't need super complex hardware to start developing your own TensorFlow models! We've curated a simple kit to dip your toes into machine ...

SKU: AF-1064 · MPN: 1064

This electret capsule microphone is the same one we use in our great microphone amplifier board. It contains a small vibrating element that will output a few milllivolts peak-to-peak. You will need an op-amp to amplify the signal, some chips are designed with the amplifier built in in which...

SKU: SF-BOB-21772 · MPN: BOB-21772

This WM8960 breakout is a low-power stereo audio codec board for adding audio input and output to digital projects. The WM8960 works as both a stereo audio ADC and DAC, using I2S for audio data while allowing settings such as I2S configuration and analogue audio routing to be controlled over I2C....

SKU: MB-11008

Me Sound Sensor is designed to detect the intensity of sound in the surrounding environment. You can use it in sound interative project such as a voice operated switch or build a dancing robot with music. Based on the power amplifier LM386 and the electret microphone, ...

SKU: AF-1935 · MPN: 1935

That's one tiny microphone! At about the size of a mature aphid, this wired Electret Microphone is perfect for your FONA. This microphone's very similar to our PCB-mount Elecret Microphone but is significantly smaller and has pre-attached 65mm long wires.  We don't have a specific datash...

SKU: AF-4020 · MPN: 4020

Everything you need to get started with the NeoTrellis M4 in one kit. This pack bundles the NeoTrellis M4 Mainboard, an acrylic enclosure, silicone elastomer button pads, and rubber feet — ready to assemble into a complete MIDI controller, sound board, or interactive button-pad device. The NeoTr...

SKU: AF-3938 · MPN: 3938

The NeoTrellis M4 Mainboard combines an ATSAMD51 Cortex M4 processor, a 4×8 grid of NeoPixel-lit elastomer button pads, stereo audio output, microphone input, and a triple-axis accelerometer into one compact, programmable board. Think of it as a button-mashing, light-flashing, tune-making powerho...

SKU: SF-SEN-15289

The SparkFun gator:microphone is a micro:bit Accessory Board that integrates an electret microphone into SparkFun's gator:bit series of gator-clippable accessories, enabling it to be easily interfaced with the micro:bit or other microcontrollers! It provides a binary indication of the presence of...

SKU: SS-101020023

The Sound sensor module is a simple microphone. Based on the power amplifier LM386 and the electret microphone, it can be used to detect the sound strength of the environment. The value of output can be adjusted by the potentiometer.   Features Grove compatible interface Wide supply vo...