All Products
Showing 1-20 of 100 products
Thumbnail Sized DC Motor Driver 2x1.5A (HR8833)
INTRODUCTION This is a ultra compact size Dual-H-Bridge dc motor driver (Based on HR8833), which could drive two way 1.5A DC brush motors up to 10V . It has the same footprint as your thumbnail suitable for projects with limited spaces. Both sides of the module are ...
SimpleFOCmini Brushless DC Motor Driver Board
·
This compact DFRobot driver board is made for precise control of brushless DC motors using Field-Oriented Control (FOC). At just 26 x 21.5mm, it is well suited to tight builds where smooth motion, low noise and responsive control matter.SimpleFOCmini supports closed-loop control of motor position...
DRV8838 Single Brushed DC Motor Driver Carrier
Overview DRV8838 Single Brushed DC Motor Driver Carrier, bottom view with dimensions. TI SN754410 (16-pin DIP) next to the #2135 DRV8835 carrier (14-pin DIP) and #2990 DRV8838 carrier (10-pin DIP) for size reference. Texas Instruments’ DRV8838 is a tiny H-bridge motor driver IC that can...
2x7A DC Motor Driver
An ultra-compact dual DC motor driver built around a robust H-bridge design with 7 A continuous current per channel and a 50 A peak rating. Opto-coupler isolation on all control signals protects your microcontroller from motor-induced reverse currents, while built-in UVLO (Under-Voltage Latch-Out...
Arduino Quad DC Motor Driver Shield
INTRODUCTION The latest quad motor driver shield for Arduino, compatible with 5V/3.3V Arduino controller, can control up to four DC motors with 8 pins at the same time. The shield supports PWM speed control and polarity control. The driver shield includes two TB6612FNG ...
15A Single DC Motor Driver
The DFRobot DRI0042 is a compact, high-current DC motor driver capable of continuously driving a single motor at up to 15A (with heatsink) from a 12–36V supply. The onboard LM2575 regulator provides a 5V 500mA output for powering an Arduino or other controller, and all control signal inputs inclu...
Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max
·
The Adafruit DRV8871 is a single-channel brushed DC motor driver breakout capable of delivering up to 3.6 A peak current with a wide 6.5–45V motor voltage range. Its resistor-set current limiting and built-in PWM support make it straightforward to use with virtually any brushed DC motor. The boa...
SyRen Single 10A DC Motor Driver
The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 30lbs in combat or 100lbs for general purpose robotics. Out of the box, the SyRen 10 can supply a single DC brushed motor with up to 10...
SyRen Single 50A DC Motor Driver
The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. Out of the box, the SyRen 50 can supply a single DC brushed motor with up to 50A continuously. Peak currents of 100A are achievable for a few seconds. Overcurrent and thermal protection me...
SyRen Single 25A DC Motor Driver
The SyRen motor driver is one of the most versatile, efficient and easy to use motor drivers on the market. It is suitable for medium powered robots - up to 50lbs in combat or 180lbs for general purpose robotics. Out of the box, the SyRen 25 can supply a single DC brushed motor with up to 25...
Sabertooth Dual 25A DC Motor Driver
The Sabertooth 2X25 is a versatile dual DC motor driver capable of supplying up to 25A continuous (50A peak) per channel. Suitable for high-powered robots up to 100lbs in combat or 300lbs for general-purpose robotics, it features synchronous regenerative drive that recharges batteries during brak...
2x1.2A DC Motor Driver with Gravity Connector (TB6612FNG)
The DFRobot 2×1.2A DC Motor Driver with Gravity Connector is a compact dual-channel motor driver based on the TB6612FNG IC. This version features standard DFRobot Gravity connectors for plug-and-play wiring with Gravity-compatible expansion boards — no soldering or breadboard needed. Each channe...
2x1.2A DC Motor Driver (TB6612FNG)
The DFRobot 2×1.2A DC Motor Driver is a compact dual-channel motor driver based on the TB6612FNG IC. It requires only four GPIO pins to control two DC motors, using the same control logic as the DFRobot L298N motor driver — making existing L298N code directly compatible. Each channel delivers up...
PPM 2x3A DC Motor Driver
This motor driver module is a special PPM signal motor controller for Aero modelling remote control. It is designed by DFRobot and it can be controlled by RC transmitter. The driver can convert PPM signal to the motor speed and direction control signal. There are two signal receiving chan...
DC Motor Driver HAT(V1.0)
The DC Motor Driver HAT is a Raspberry Pi add-on board that drives up to two DC motors via I2C. Built around the TB6612FNG motor driver chip with 1.2 A continuous current per channel (2 A peak), it supports both standard DC motors and motors with encoders through the on-board encoder interface. ...
MP6550 Single Brushed DC Motor Driver Carrier
The MP6550 from Monolithic Power Systems (MPS) is an H-bridge motor driver IC that can be used for bidirectional control of one brushed DC motor at 1.8 V to 22 V. It can supply up to about 1.7 A continuously and features configurable current sensing and current limiting. Since this board is a car...
DRV8874 Single Brushed DC Motor Driver Carrier
This compact breakout board for TI’s DRV8874 motor driver offers a wide operating voltage range of 4.5 V to 37 and can deliver a continuous 2.1 A (6 A peak) to a single bidirectional brushed DC motor. The DRV8874 also features integrated current sensing and regulation as well as built-in pr...
2x3A DC Motor Driver Carrier Board for UNIHIKER M10
·
This DFRobot motor driver carrier board is purpose-built for the UNIHIKER M10, featuring a tilted edge connector slot that positions the screen at an optimal viewing angle. It integrates a dual 3 A DC motor driver with separate motor power, plus onboard RGB LEDs and infrared transmitter/receiver....
Dual-Channel DC Motor Driver-12A
This is a dual channel DC motor driver with an extremely small size of of 1.97”×1.97”×0.49”. The module comes with two motor channels that can drive two motors simultaneously, and each channel employs an indicator to show the rotation direction of the motor: blue is forward rotation, red is rever...
Cytron MOTION 2350 Pro RP2350 Robotics Controller
·
Built around Raspberry Pi’s RP2350 processor, this Cytron robotics controller is made for beginner and intermediate builders who want to create more advanced robots while spending less time on the supporting electronics.The board integrates a 4-channel brushed DC motor driver, servo outputs, GPIO...
