All Products

SKU: AF-1871

A sewable breakout board with a CR2032 coin cell battery holder, built-in on/off switch, and 0.1" pitch breakout pins. The board provides two ground pins, one switched power pin, and one always-on power pin — giving you flexibility in how you manage power in your project. Also available: version...

SKU: AF-783

A compact coin cell battery holder designed for small portable and wearable electronics projects. It holds two 20mm coin cells (CR2032 is the most common size) wired in series to provide 6V nominal output, with an on/off switch built into the top for convenient power control. The holder features...

SKU: AF-1870

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit to a real-time clock or similar module. Key Features CR2032 Coin Cell Holder ...

SKU: LB-BK-LR0347A

A sewable coin cell battery holder with built-in on/off slide switch, designed for e-textile and wearable electronics projects. This bulk 10-pack is ideal for classrooms, workshops, and makerspaces. Each holder accepts a standard 20 mm coin cell battery (CR2032) and features sewable tabs for eas...

SKU: SF-DEV-13883

Sure, your flashing, chip-tune playing T-shirt is really cool at the party… but at some point you need to turn it off. And yes, you could just pull the battery, or maybe you’ve even sewn a LilyPad slide switch in-line. Wouldn’t it be nice if there was just a switch on the battery? Well, look no f...

SKU: LB-LR0347A

This E-Textiles  Coin Cell Battery Holder has a small slide switch installed on the board, in-line with the power so you can shut off your project and save batteries. This slide switch is the same as is found on the LilyPad slide switch board, so it’s not easy to accidentally turn off or on....

SKU: LB-PRT-12618

An enclosed coin cell battery holder for two CR2032 batteries wired in series, delivering up to 6 V output. The holder features a built-in on/off slide switch and two 150 mm (6″) power leads (positive and negative). A secure screw-down enclosure with two Phillips head screws keeps batteries safel...

SKU: LB-SMILE

This is a simple coin cell battery holder that can enclose two CR2032 batteries inside itself, and safely kept closed via two phillips head screws. Each battery holder will run batteries in series, output up to 6V, and is equipped with an On/Off slide switch and two 4" power wires (one positive a...

SKU: LB-EAGLED

EagLED is Little Bird's wearable development kit — a complete Arduino-compatible microcontroller on a snappable board with built-in LEDs, a light sensor, push button, and battery holder. Snap apart the components, sew them onto fabric, and bring your wearable project to life. With built-in USB s...

SKU: KI-2715

A starter kit for e-textiles and wearable electronics from Kitronik's Electro-Fashion range. This Discovery Pack includes a curated selection of sewable components — LEDs, switches, coin cell holders, conductive thread, and batteries — everything you need to begin adding electronics to fabric pro...

SKU: LB-PAPER-SCREW

A child-safe battery holder designed for paper circuits in educational settings. Features a screw-secured enclosure for the CR2032 coin cell battery, meeting ACCC safety guidelines for button batteries used around children. Includes a breakout board for direct copper tape connection. Paper circu...

SKU: LB-EAGLED-BUZZ-KIT

The EagLED is Little Bird Electronics' own Arduino-compatible wearable development kit, designed from the ground up for e-textile projects. It packs a microcontroller, LEDs, light sensor, push button, and buzzer onto a snippable board — with snap-off satellite boards for eyes, stars, and hearts t...

SKU: AF-1850

Add a touch of sparkle to your wearables with the Adafruit Gemma Sequin Starter Pack. This beginner-friendly kit includes a GEMMA V2 sewable microcontroller, warm white LED sequins, conductive thread, needles, and a coin cell battery holder — everything you need to start sewing glowing electronic...

SKU: LB-CR2032-SAFE

A child-safe, screw-closed battery enclosure for a single CR2032 coin cell, designed to meet ACCC button battery safety guidelines. The compartment requires a screwdriver to open, preventing young children from accessing the battery. A breakout board on the enclosure allows you to apply copper ta...

SKU: AF-3672

This kit is designed for use with the electronic textiles unit in the Exploring Computer Science (ECS, exploringcs.org) introductory computing curriculum for secondary students. It contains most of the materials needed for four e-textiles projects: paper circuit, wristband, mural, and hum...

SKU: PI-EMS000074

The Boldport Buggy is a charming soldering kit designed by Saar Drimer of Boldport, originally created as a badge for the hardwear.io hardware security conference in The Hague. With its posable resistor legs, flickering LED eyes, and bendable antennae, the finished bug has plenty of personality. ...

SKU: SF-DEV-08822

A 20 mm coin cell battery holder designed for CR2032 batteries. The holder features a pop-in, pop-out mechanism for easy battery changes, and the mounting feet include small holes for sewing onto fabric — making it suitable for e-textile and wearable electronics projects as well as standard PCB u...

SKU: AF-1657

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a U...

SKU: SF-KIT-14528

The LilyPad E-Sewing ProtoSnap Kit is a great way to incorporate buttons and switches into an e-textile project without any programming required. Like other LilyPad ProtoSnap series boards, the individual pieces of the included E-Sewing ProtoSnap are pre-wired — allowing you to try out the f...

SKU: LB-JSTBOARD

This E-textiles board is a breakout for a JST, so you can sew it onto a garment or use it in Paper Circuits! The JST breakout board can be easily sewn through the large holes. For paper circuits, simply apply copper tape on top of it.A wearable lithium polymer battery or wearable lipo also kno...