All Products
Showing 81-100 of 100 products
NPN to PNP Signal Converter / Adapter Module
This NPN to PNP signal converter module bridges the gap when your sensor outputs an NPN signal but your controller or PLC expects a PNP input. Simply wire it inline between the sensor and the controller to convert the signal type without modifying either device. The module includes built-in surg...
2.3KG Serial Bus Servo (6V)
A miniature serial bus servo from DFRobot that delivers 2.3 kg·cm of stall torque at 6 V, controllable via TTL serial communication. Up to 253 servos can be daisy-chained in series, each assigned a unique ID for individual or synchronised control at baud rates up to 1 Mbps. The hybrid gear train...
Adafruit NAU7802 24-Bit ADC - STEMMA QT / Qwiic
·
The Adafruit NAU7802 is a high-resolution 24-bit differential ADC breakout designed specifically for reading strain gauges, load cells, and other Wheatstone bridge sensors. With built-in gain amplification and calibration circuitry, it converts the tiny voltage changes from bridge sensors into pr...
SparkFun OpenLog Artemis (without IMU)
The SparkFun OpenLog Artemis (OLA) is an open-source data logger built on the Artemis module (Cortex-M4F Apollo3 microcontroller). It comes pre-programmed to automatically detect, configure, and log data from Qwiic-enabled sensors — no coding required. Simply plug in a compatible sensor, power up...
Fermion: 1.8" 128x160 IPS TFT LCD Display with MicroSD Card Slot (Breakout)
A 1.8-inch IPS TFT LCD display module with 128×160 resolution and an integrated microSD card slot for reading full-colour bitmaps. Driven by the ST7735S chip over SPI (4-wire), the display offers a 120° viewing angle and low power consumption, making it suitable for sensor dashboards, status moni...
Gravity: I2C 4-20mA DAC Module (Arduino Compatible)
The Gravity I2C 4-20mA DAC Module outputs 0–25 mA of current controlled via I2C, with high-accuracy 4–20 mA output available after calibration (0.2% linearity error). Built around the GP8302 chip, it provides 12-bit resolution and is compatible with Arduino, enabling precise current-loop control ...
Direct-Drive Servo Motor for Robotics and AGV Drive Wheel (UART, 210rpm)
·
A compact direct-drive servo motor integrating a brushless outer-rotor motor, encoder, and servo driver into a single unit. By eliminating the traditional gearbox/reducer, it delivers smooth torque, low noise, and long life in a smaller package. The built-in driver uses a Field-Oriented Control ...
High Torque Waterproof Digital Servo with Magnetic Encoder (25KG, 360°, IP54)
·
##Introduction This is an exceptional high-torque, waterproof digital servo with a magnetic encoder, boasting a maximum torque of 25kg. It features a 12-bit high-precision magnetic encoder sensor that allows for precise and absolute control of the servo's position within a 360-degree range, ensur...
ESP32-Based Robotic Arm Kit – 5+1 DOF, High-Torque, 2-DOF Wrist
·
5 + 1 DOF High-Torque Serial Bus Servo Robotic Arm Kit Unleash the Power of Robotic Precision with the RoArm-M3 Series Unrivaled Strength and Flexibility Welcome to a world of cutting-edge robotics with our RoArm-M3, a 5 + 1 DOF serial bus servo robotic arm built for high-precision tasks and ada...
Multi Function Expansion Board for UNIHIKER K10 and micro:bit (Power and Motion)
·
##Introduction The Multi-function Expansion Board for UNIHIKER is an all-in-one solution designed to unlock the full potential of UNIHIKER K10 projects. It directly addresses common hurdles by integrating a powerful motor driver, a portable power supply system, and extensive I/O expansion onto a ...
INA237 Qwiic Current Sensor
·
Monitor DC current and power over I2C with this Qwiic breakout based on the Texas Instruments INA237 digital power monitor. It measures current, bus voltage, internal temperature and power for an in-line DC input using a 16-bit delta-sigma ADC.The board is set up for flexible wiring: use the pair...
Load Cell - 10kg, Straight Bar (TAL220)
A straight bar load cell (strain gauge) that translates up to 10 kg of force into an electrical signal. Built from aluminium alloy with four strain gauges in a Wheatstone bridge configuration, it measures the change in electrical resistance proportional to the applied load. Use it to weigh objec...
Load Cell - 200kg, Disc (TAS606)
This disc load cell (sometimes called a strain gauge) can translate up to a whopping 200kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to th...
SparkFun Load Cell Amplifier - HX711
The SparkFun Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. By connecting the amplifier to your microcontroller you will be able to read the changes in the resistance of the load cell, and with some calibration you’ll be...
Load Cell - 200kg, S-Type (TAS501)
This S-Type load cell (sometimes called a strain gauge) can translate up to 200kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response and proportion to the strain (e.g., pressure or force) applied to the form. With th...
Load Cell - 5kg, Straight Bar
This straight bar load cell (strain gauge) converts applied force or weight into a proportional electrical signal, with a maximum capacity of 5kg. It uses four strain gauges arranged in a Wheatstone bridge configuration for accurate, stable readings — ideal for building digital scales, weight mon...
Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070
·
This breakout board is the simplest way to create a project with mutiple capacitive touch sensors. No microcontroller is required here - just power with 1.8 to 5.5VDC and connect up to 5 conductive pads to the 5 left-hand pins. When a capacitive load is detected (e.g. a person touches one of the ...
Mini Load Cell - 500g, Straight Bar (TAL221)
This miniature straight bar load cell (sometimes called a strain gauge) can translate up to 500g of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) ap...
Load Cell - 5kg, Straight Bar (TAL220B)
A straight bar load cell (strain gauge) that translates up to 5kg of force into an electrical signal. Made from aluminium alloy with four strain gauges in a Wheatstone bridge configuration, it measures electrical resistance changes proportional to the applied load. Use it to measure object weigh...
Mini Load Cell - 100g, Straight Bar (TAL221)
This miniature straight bar load cell (sometimes called a strain gauge) can translate up to 100g of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) ap...
