All Products

SKU: SF-DEV-21247

The SparkFun USB-C Host Shield provides all the digital logic and analogue circuitry needed to add USB peripheral/host control to your Arduino. Interface with and control any USB 2.0 compatible device — thumb drives, digital cameras, Bluetooth dongles, game controllers, and more. This version up...

SKU: SF-PRT-12711

The SparkFun USB LiPoly Charger is a single-cell Li-Ion/Li-Polymer battery charging board based on the MCP73831T. It charges 3.7V LiPo cells at a selectable rate of 500 mA or 100 mA via a solder jumper, with power input from either USB or a barrel jack connector. The board includes a SYS OUT JST...

SKU: SF-BOB-10031

We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all 5 pins with a vertical microUSB connector for your prototyping needs. Documents: Schematic Eagle Files GitHub

SKU: SF-BOB-09966

A simple breakout board for the USB Mini-B connector, bringing all 5 pins out to a breadboard-friendly 0.1" pitch header. Useful for prototyping USB connections or as a convenient 5V power source (up to 100 mA, unregulated). Key Features All 5 Pins Broken Out – VCC, D-, D+, ID, and GND Breadb...

SKU: SF-CAB-11301

A 6-foot (1.8 m) USB 2.0 cable with a Type-A plug on one end and a Mini-B 5-pin plug on the other. Use it to connect cameras, USB hubs, FTDI programmers, LiPo chargers, and other devices that use the Mini-B connector. Specifications Connector A – USB Type-A (male) Connector B – USB Mini-B 5-p...

SKU: SF-SWG-14658

With the cost of microSD cards on a consistent rise, it’s always useful to have an economical and reliable option as a backup for storing your files. This sleek, red 16GB thumb drive has been emblazoned with our SparkFun Electronics logo and our moniker to Start Something! Each thumb drive featu...

SKU: SF-BOB-09822

This is the newest revision and fixes issues with the last board. This breakout board pairs an SP3485 RS-485 transceiver with an FT232RL USB UART IC to convert a USB stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transm...

SKU: SF-BOB-12731

This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip. With this version...

SKU: SF-BOB-12700

This simple breakout board routes a female USB Type-A connector's VCC, GND, D−, and D+ pins to a standard 0.1″ pitch header. It saves you the hassle of soldering tiny SMD connectors when adding USB host or device connectivity to your project. Key Features Female USB Type-A Connector – Accepts ...

SKU: SF-BOB-13830

The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get t...

SKU: SF-BOB-11771

This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA acc...

SKU: SF-SEN-22857

Virtual reality is in, but you shouldn't have to drop hundreds of dollars to gain access to the technology behind it. Luckily, that's where the SparkFun VR IMU Breakout comes in. At its heart is CEVA’s BNO086, a combination triple-axis accelerometer/gyro/magnetometer System in Package (SiP) with ...

SKU: SF-DEV-15837

The SparkFun weather:bit is a fully loaded "carrier" board for the micro:bit that, when combined with the micro:bit, provides you with a fully functional weather station. With the weather:bit you will have access to barometric pressure, relative humidity and temperature readings. There are ...

SKU: SF-KIT-10723

Have you ever seen a Weevil? It’s a pretty under-appreciated beetle, so we thought it deserved a kit. Okay, so we just kind of like the name and think it makes a cute board. The WeevilEye is a through-hole soldering kit designed for the beginner. It has a low parts count so even young kids can ea...

SKU: SF-WRL-13287

The SparkFun ESP8266 WiFi Shield is an Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. There are a variety of designs based around the ESP8266, including tiny, modular boards and more accessible development boards l...

SKU: SF-KIT-14051

The SparkFun Wireless Joystick Kit gives you a customisable wireless controller for XBee-based projects. Built around the SAMD21 microcontroller, it provides a flexible alternative to hobby RC transmitters — configure it your way at a fraction of the cost. The kit can be assembled in two configu...

SKU: SF-DEV-14285

The SparkFun Wireless Motor Driver Shield is designed to make connecting motors, sensors and other components to your Arduino-based project as fast and easy as possible. The heart of the Wireless Motor Driver Shield is the Toshiba TB6612FNG H-Bridge Motor Driver, which allows the shield to contro...

SKU: SF-KIT-15936

This is the SparkFun XBee 3 Wireless Kit, the perfect box full of goodies to get you started using XBees. Inside this kit you will find two XBee 3 Modules, one XBee Explorer, one Xbee Shield and a set of Arduino R3 headers to solder onto the shield. Our entire goal for the XBee Kit was to make wi...

SKU: SF-WRL-11697

This is the SparkFun XBee Explorer Dongle unit for the Digi XBee module line. With the XBee Explorer Dongle you can plug the unit directly into your USB port and have it act as a gateway between your computer and the XBee. No cables needed! This unit works with all XBee modules including the Seri...

SKU: SF-WRL-11373

The SparkFun XBee Explorer Regulated takes care of the 3.3V regulation, signal conditioning, and basic activity indicators (Power, RSSI and DIN/DOUT activity LEDs). It translates the 5V serial signals to 3.3V so that you can connect a 5V (down to 3.3V) system to any XBee module. The board was con...