All Products

SKU: SF-WIG-09555

This board allows you to interface with your car’s OBD-II bus. It provides you a serial interface using the ELM327 command set and supports all major OBD-II standards such as CAN and JBUS. The board also provides a footprint which mates directly to our FTDI Basic or a Bluetooth Mate. The DB9 conn...

SKU: SF-BOB-09816

This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the feedback path. The bandwidth is set to 15.9kHz by a pair of feedback capacitors, or over 100kHz with the...

SKU: SF-DEV-13712

The SparkFun OpenLog is an open-source serial data logger based on the ATmega328 running at 16 MHz. It logs incoming serial data directly to a microSD card, supporting cards from 64 MB to 64 GB in FAT16 or FAT32 format. Simply connect a serial line from your project to the OpenLog, and all transm...

SKU: SF-DEV-16832

The SparkFun OpenLog Artemis is an open source data logger that comes preprogrammed to automatically log IMU, GPS, serial data, and various pressure, humidity, and distance sensors. All without writing a single line of code! OpenLog Artemis, or "OLA," automatically detects, configures, and logs Q...

SKU: SF-DEV-19426

The SparkFun OpenLog Artemis (OLA) is an open-source data logger built on the Artemis module (Cortex-M4F Apollo3 microcontroller). It comes pre-programmed to automatically detect, configure, and log data from Qwiic-enabled sensors — no coding required. Simply plug in a compatible sensor, power up...

SKU: SF-KIT-20684

The Air Quality Monitoring version of the SparkFun OpenLog Data Collector Kit with Machinechat is an easy way to organize and display your data from an included SGP40 Qwiic Air Quality Sensor with the OpenLog Artemis and JEDI One. The SparkFun OpenLog Artemis (without IMU) is an open source data ...

SKU: SF-KIT-20673

The Base version of the SparkFun OpenLog Data Collector Kit with Machinechat is an easy way to organize and display your data with the OpenLog Artemis and JEDI One. The SparkFun OpenLog Artemis (without IMU) is an open source data logger that comes preprogrammed to automatically log GPS / GNSS, s...

SKU: SF-KIT-20683

The Environmental Monitoring version of the SparkFun OpenLog Data Collector Kit with Machinechat is an easy way to organize and display your data from an included BME280 Qwiic Atmospheric Sensor with the OpenLog Artemis and JEDI One. The SparkFun OpenLog Artemis (without IMU) is an open source da...

SKU: SF-DEV-13955

The SparkFun OpenLog with Headers is an open source data logger that works over a simple serial connection and supports microSD cards up to 64GB. The OpenLog can store or "log" huge amounts of serial data and act as a black box of sorts to store all the serial data that your project generates, fo...

SKU: SF-SEN-13261

The SparkFun OpenScale is an open-source weight measurement board designed for load cells. Simply connect a four-wire or five-wire load cell of any capacity, plug into USB, open a serial terminal at 9,600 bps, and you'll immediately see mass readings. A built-in serial menu lets you configure cal...

SKU: SF-SEN-24904

The SparkFun Qwiic Optical Tracking Odometry Sensor empowers you to elevate your robot's navigation capabilities with exceptional precision and streamlined integration. This compact, all-in-one sensor leverages the power of the PAA5160E1 chip from PixArt Imaging Inc., delivering accurate dual-axi...

SKU: SF-BOB-09118

This is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system. This board electrically isolates a controller from the high-power system by use of an opto-isolator IC. This IC has two LEDs and two pho...

SKU: SF-KIT-15817

The SparkFun Paper Circuits Kit introduces the basics of electronic circuits without any soldering or coding. Using copper tape, LEDs, and printed templates, you build 10 light-up robot cards that each take 5–10 minutes to assemble — a fun, hands-on way to learn about circuits for all ages and ex...

SKU: SF-TOL-11640

When you’re working with e-textiles, you have a tendency to collect a lot of small parts: LilyPad boards, bobbins, needles, the tools of the trade. Why not pick up a sturdy little box to keep your bits and pieces off the floor? This LilyPad branded box is made from rigid cardboard printed with a ...

SKU: SF-TOL-15295

One ruler to rule them all. This is a basic 12 inch ruler, but made from a PCB. We have included a lots of useful information on each side of the ruler that you might use on a daily basis including Wire Gauge holes, transistor diagrams, common fractions, Roman numerals, and metric to imperial con...

SKU: SF-SEN-22956

The SparkFun Photoacoustic Spectroscopy CO2 Sensor features the Infineon XENSIV PAS CO2 (PASCO2V01) sensor, which delivers highly accurate CO2 measurements in direct parts-per-million (ppm) format. The photoacoustic spectroscopy system combines narrow-band filtered IR light with a sensitive micro...

SKU: SF-SEN-16474

The SparkFun Photodetector Breakout is an updated version of the SparkFun Particle Sensor Breakout includes the MAX30101, a highly sensitive optical sensor and successor to the MAX30105 and MAX30102. The MAX30101 Breakout utilizes a photon detector to measure the amount of returning light that is...

SKU: SF-BOB-09322

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>4.9V). When the gate is blocked by a finger, writing utensil, food pellet, or an...

SKU: SF-DEV-13321

The SparkFun Photon RedBoard, to put it simply, is a WiFi/Microcontroller development board in the Arduino form-factor for the Photon. It’s easy to use, it’s powerful, and it’s connected to the cloud. With the best support, potential, and performance the Photon RedBoard provides you with an IoT d...

SKU: SF-KIT-13863

The SparkFun PicoBoard Starter Kit is your go-to source to begin learning everything about the SparkFun PicoBoard and the Scratch programming environment. This kit includes your very own PicoBoard, multiple pieces of hardware to get you started, and connecting components to get you hooked up. ...