All Products

SKU: AF-3905

This compact 2×2 AA battery holder connects four AA batteries in series, providing a nominal 6 V DC output (alkaline) or 4.8 V DC (rechargeable NiMH). The premium jumper header wires plug directly into a breadboard — no stripping or soldering required for prototyping. The square 2×2 configuratio...

SKU: DF-DRI0017

The DFRobot 2×2A Motor Shield uses the L298P dual full-bridge driver chip to control two 4.8–35 V DC motors at up to 2 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using PWM pins 10 and 11 for speed control and digital pins 12 and 13 for enable/disable. The shield ...

SKU: DF-DRI0009

The DFRobot 2×2A DC Motor Shield uses the L298P dual full-bridge driver chip to control two DC motors at up to 2 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using PWM pins 5 and 6 for speed control and digital pins 4 and 7 for enable/disable. The shield can be pow...

SKU: DF-DFR1136 · MPN: DFR1136

This DFRobot motor driver carrier board is purpose-built for the UNIHIKER M10, featuring a tilted edge connector slot that positions the screen at an optimal viewing angle. It integrates a dual 3 A DC motor driver with separate motor power, plus onboard RGB LEDs and infrared transmitter/receiver....

SKU: SF-PRT-10877

This 2×3 (6-pin) shrouded header with 2.54 mm (0.1″) pitch provides a keyed connection that prevents cable mishaps. The shroud ensures correct orientation when connecting ribbon cables or IDC connectors. Key Features 6-Pin (2×3) – Dual-row header layout Shrouded/Keyed – Prevents incorrect cab...

SKU: AF-3342

This 2×40 right-angle edge connector fits directly onto the bottom edge contacts of the BBC micro:bit, providing access to all GPIO pins, power, and ground connections. The right-angle design is ideal for mounting on custom PCBs. The connector has 80 pins total, but because the micro:bit edge co...

SKU: LB-LS6972x2

A compact stereo speaker pair for small audio projects, handheld devices, and embedded builds. Each 45mm driver is rated at 4Ω and 3W, delivering clear, balanced sound in a slim form factor. Pre-wired with a PH2.0 plug for quick connection to common audio amplifier boards. Key Features Stereo ...

SKU: SF-PRT-08535

This 2×5 (10-pin) IDC ribbon cable with 2.54 mm pitch connectors is commonly used for AVR ISP programming and general-purpose communication between boards. The cable is 6 inches (approximately 15 cm) in length. Key Features 10-Pin (2×5) – Standard AVR ISP programming pinout IDC Connectors – K...

SKU: SF-PRT-08506

A 2×5 (10-pin) shrouded box header on standard 0.1" (2.54 mm) pitch. The keyed shroud prevents reversed cable connections, making it ideal for programming headers, data buses, and other multi-pin interfaces. Key Features Shrouded & Keyed – Polarised housing prevents incorrect cable orientation...

SKU: DF-DRI0041

An ultra-compact dual DC motor driver built around a robust H-bridge design with 7 A continuous current per channel and a 50 A peak rating. Opto-coupler isolation on all control signals protects your microcontroller from motor-induced reverse currents, while built-in UVLO (Under-Voltage Latch-Out...

SKU: KI-2271

A compact 2×AAA battery cage with a JST PH connector and 145 mm colour-coded leads. Designed to plug directly into the BBC micro:bit's battery socket, providing a portable power source for classroom projects and wearable builds. Key Features JST PH Connector – Plugs directly into the micro:bit...

SKU: DF-FIT0625 · MPN: FIT0625

This compact battery holder is a handy portable power pack for small electronics and maker projects. It holds two AAA batteries and connects them in series, making it suitable for projects that need a simple removable battery supply.The holder includes a cover and an integrated power switch, so y...

SKU: AF-4191

A slim 2×AAA battery holder with a built-in on/off switch and genuine JST PH connector. Two AAA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds. The JST PH connector polarity matches Adafruit's Li-Ion/LiPo ...

SKU: PI-COM1305

A compact 2×AAA battery holder with a built-in power switch and JST connector, compatible with micro:bit and other boards that accept JST battery inputs. This is the same battery holder included in our micro:bit accessories kit. Key Features Power Switch – On/off switch for convenient power co...

SKU: AF-4192

A slim, open-top 2×AAA battery holder with a genuine JST PH connector. Two AAA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and boards with JST PH battery inputs. The JST PH connector polarity matches Adafruit's Li-Ion/LiPo...

SKU: AF-3951

A 2×AA battery holder with a built-in knife switch for controlling power. Unlike typical slide switches, the knife switch provides a clear visual indicator of open and closed circuit states — making it an excellent tool for teaching basic electronics and circuit concepts. The holder takes two AA...

SKU: EF-EF10095

A 2×AA battery holder designed specifically for the BBC micro:bit. The built-in JST PH connector plugs directly into the micro:bit's battery socket, and the integrated on/off switch with a secure cover provides safe, convenient power control. Key Features micro:bit Compatible – JST PH connecto...

SKU: AF-4193

A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds without needing to disconnect the battery to turn off power. The...

SKU: AF-3858

A 2×AA battery holder with premium jumper header wires that plug directly into a breadboard — no stripping, twisting, or fighting with thin leads. Two AA batteries in series provide approximately 2.5V to 3V, making this a convenient power source for breadboard prototyping. Key Features Breadbo...

SKU: AF-4194

A slim, open-top 2×AA battery holder with a genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, Adafruit boards, and microcontrollers with JST PH battery inputs. The JST PH connector polarity matches Adafruit's Li-I...