All Products
Showing 1-20 of 100 products
LilyPad Temperature Sensor
Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient...
ProtoSnap - LilyPad Development Board
The ProtoSnap series is a new way to prototype your project without a breadboard. Everything is wired together on a single board, which makes it easy to explore the possibilities of the components before snapping them apart and building them into your project. The ProtoSnap LilyPad Development...
Gravity: MOSFET Power Controller
In most Arduino projects, relays are the first choice to drive some large current device. It requires a certain amount of current to drive the internal coil to pick-up contact. But for some MCU, like Intel Edison, Intel joule, lilypad, Raspberry Pi and other microcontroller with limited amoun...
PT100 Platinum RTD Temperature Sensor
·
This PT100 is a platinum RTD (Resistance Temperature Detector) for accurate temperature sensing. It has a nominal resistance of 100Ω at 0°C, with resistance changing as temperature changes.It is suitable for applications across a broad temperature range, and is commonly used where stable, repeata...
Adafruit TMP119 ±0.03°C I2C Temperature Sensor
·
Built around Texas Instruments' TMP119, this breakout makes it easy to add extremely accurate temperature monitoring to your project over I2C. It is designed for applications where temperature really matters, including thermostats, cold chain asset tracking, and gas or heat metering, and it can a...
LM35DZ
The LM35DZ is a simple temperature sensor IC for projects that need low-cost temperature measurement with good accuracy around room temperature.It is suited to remote sensing applications and runs from a broad 4 to 30 V supply range, with very low current drain to help minimise self-heating.Its l...
Gravity BMP581 Barometric Pressure & Temperature Sensor - I2C/UART
·
This compact Gravity module brings Bosch BMP581 pressure and temperature sensing to microcontroller projects that need stable altitude or environmental readings. It is designed for applications such as drone altitude hold, indoor navigation, weather logging and hiking altimeters.The board support...
Gravity BMP585 Barometric Pressure & Temperature Sensor (I2C/UART)
·
Built around the Bosch BMP585 chip, this Gravity module measures barometric pressure and temperature for altitude, weather and environmental sensing projects. Its gel-filled cavity and industrial protective cover help it resist water, moisture and chemical exposure, making it better suited to dem...
Fermion BMP581 Barometric Pressure & Temperature Sensor
·
This compact Fermion module is built around Bosch Sensortec’s BMP581 high-performance barometric pressure sensor chip. It measures pressure and temperature with high precision, offering ±0.3 hPa typical absolute pressure accuracy for detecting small altitude, floor-level or liquid-level changes.T...
Fermion BMP585 Pressure & Temperature Sensor - I2C/SPI/I3C
·
This compact Fermion breakout brings the Bosch BMP585 MEMS pressure and temperature sensor to a tiny board for projects where space, power use and reliable environmental sensing matter. It measures barometric pressure for altitude and vertical movement applications, with typical absolute pressure...
MLX90632 FIR Remote Thermal Temperature Sensor
·
This compact breakout uses Melexis' MLX90632 FIR sensor to read the temperature of a target without making contact. It's handy for checking surfaces that are hot, cold, moving, delicate or awkward to reach with a probe, and it can also report its own local on-chip temperature.The fitted MLX90632S...
1-Wire Digital Temperature Sensor for Raspberry Pi - Unassembled (1m)
The Little Bird 1-Wire Digital Temperature Sensor for Raspberry Pi — a plug-and-play solution for environment sensing, data logging, and IoT applications. Simply plug it onto the Raspberry Pi GPIO header — no breadboard, jumper wires, or additional components needed. This is the unassembled vers...
Waterproof DS18B20 Digital Temperature Sensor For Arduino
This is a waterproofed version of the DS18B20 Temperature sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get ...
Gravity: Analog High Temperature Sensor
What sensor should you use when you need to measure temperature? Most people will think of a DS18B20 temperature sensor first, but this sensor is only capable of measuring temperatures up to 125C. In order to measure temperatures greater than 100C you will need something with a greater temp...
High Temp Waterproof DS18B20 Digital temperature sensor + extras
·
This is a pre-wired and waterproofed version of the DS18B20 sensor made with a PTFE wire cable. Handy for when you need to measure something far away, or in wet conditions. This sensor is a little more expensive than the other waterproof version we have with a PVC cable because this one can be...
Adafruit PT100 RTD Temperature Sensor Amplifier - MAX31865
·
The Adafruit PT100 RTD Temperature Sensor Amplifier is a breakout board for the MAX31865 precision RTD-to-digital converter. It reads 2-, 3-, or 4-wire PT100 platinum resistance temperature detectors over SPI, delivering laboratory-grade temperature accuracy and repeatability that surpasses therm...
Temperature Sensor - TMP36
This is the same temperature sensor that is included in our SparkFun Inventor’s Kit. The TMP36 is a low voltage, precision centigrade temperature sensor. It provides a voltage output that is linearly proportional to the Celsius temperature. It also doesn’t require any external calibration to prov...
Temperature Sensor - Waterproof (DS18B20)
This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a centra...
Waterproof DS18B20 Digital temperature sensor + extras
·
This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get an...
DS18B20 Digital temperature sensor + extras
·
These 1-wire digital temperature sensors are fairly precise (±0.5°C over much of the range) and can give up to 12 bits of precision from the onboard digital-to-analog converter. They work great with any microcontroller using a single digital pin, and you can even connect multiple ones to the s...
