All Products
Showing 7521-7540 of 8668 products · 2504 unavailable products hidden
SparkFun Opto-isolator Breakout
This is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system. This board electrically isolates a controller from the high-power system by use of an opto-isolator IC. This IC has two LEDs and two pho...
SparkFun Parts Box - LilyPad (Magnetic)
When you’re working with e-textiles, you have a tendency to collect a lot of small parts: LilyPad boards, bobbins, needles, the tools of the trade. Why not pick up a sturdy little box to keep your bits and pieces off the floor? This LilyPad branded box is made from rigid cardboard printed with a ...
SparkFun PCB Ruler - 12 Inch
One ruler to rule them all. This is a basic 12 inch ruler, but made from a PCB. We have included a lots of useful information on each side of the ruler that you might use on a daily basis including Wire Gauge holes, transistor diagrams, common fractions, Roman numerals, and metric to imperial con...
SparkFun Photoacoustic Spectroscopy CO2 Sensor - PASCO2V01 (Qwiic)
The SparkFun Photoacoustic Spectroscopy CO2 Sensor features the Infineon XENSIV PAS CO2 (PASCO2V01) sensor, which delivers highly accurate CO2 measurements in direct parts-per-million (ppm) format. The photoacoustic spectroscopy system combines narrow-band filtered IR light with a sensitive micro...
SparkFun Photo Interrupter Breakout Board - GP1A57HRJ00F
A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>4.9V). When the gate is blocked by a finger, writing utensil, food pellet, or an...
SparkFun Photon RedBoard
The SparkFun Photon RedBoard, to put it simply, is a WiFi/Microcontroller development board in the Arduino form-factor for the Photon. It’s easy to use, it’s powerful, and it’s connected to the cloud. With the best support, potential, and performance the Photon RedBoard provides you with an IoT d...
SparkFun Picoboard Starter Kit
The SparkFun PicoBoard Starter Kit is your go-to source to begin learning everything about the SparkFun PicoBoard and the Scratch programming environment. This kit includes your very own PicoBoard, multiple pieces of hardware to get you started, and connecting components to get you hooked up. ...
SparkFun PIR Breakout - 170uA (EKMC4607112K)
Passive Infrared (PIR) sensors are great for detecting motion in a small area around the sensor. The 170µA SparkFun EKMC4607112K PIR Breakout is a simple board equipped with an EKM-series PIR sensor from Panasonic®. The EKM-series PIR sensors are optimized for small movements to offer motion-sens...
SparkFun PIR Breakout Starter Kit (170uA)
The SparkFun 170uA PIR Breakout Starter Kit comes with everything you need to get started using Passive Infrared (PIR) sensors. PIR sensors are great for detecting motion in a small area around the sensor. The 170µA SparkFun EKMC4607112K PIR Breakout is a simple board equipped with an EKM-series ...
SparkFun PIR Breakout Starter Kit (1uA)
The SparkFun PIR Breakout Starter Kit includes everything needed to get started with passive infrared motion detection. Built around the Panasonic EKMB1107112 PIR sensor, this kit's breakout board offers ultra-low 1µA standby current, making it ideal for battery-powered motion-sensing application...
SparkFun Pi Wedge (Preassembled)
This is the SparkFun Pi Wedge, a small board that connects to the 40-pin GPIO connector on the Raspberry Pi and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a couple of decoupling capacitors on the power supply lines. The “Wedge” also makes the initial b...
Sparkfun Pi Zero USB Stem
The Pi Zero USB Stem is a PCB kit that turns a Raspberry Pi Zero into a USB dongle. Once the Stem is installed, your Raspberry Pi can be plugged directly into a computer or USB hub without any additional cables or power supplies. The Raspberry Pi then acts as a USB device using its own Linux kern...
SparkFun Power Delivery Board - USB-C (Qwiic)
The SparkFun Power Delivery Board uses the STMicroelectronics STUSB4500 controller to negotiate USB Power Delivery (PD) contracts with compatible chargers and adapters. Instead of being limited to 5 V from a standard USB connection, this board can request higher voltages — typically 5–20 V and up...
SparkFun Power Driver Shield Kit
The SparkFun Power Driver Shield Kit lets you switch high-current loads directly from your Arduino using six RFP30N06LE N-channel MOSFETs. Connect a computer power supply or other DC source to drive motors, solenoids, LED strips, and other power-hungry devices with PWM control. Each of the six c...
SparkFun Pressure Sensor Breakout - MS5803-14BA
This is the MS5803-14BA Pressure Sensor Breakout, a high resolution pressure sensor with both an I2C and SPI interface. This MEMS pressure sensor measures the absolute pressure of the fluid around it which includes air, water, and anything else that acts like a viscous fluid. Depending on how you...
SparkFun ProDriver - Stepper Motor Driver (TC78H670FTG)
The SparkFun ProDriver makes it easy to start developing with the TC78H670FTG bipolar stepper motor driver from Toshiba! Latch terminals provide instant solder-less connections to every feature offered. Use our extensive Arduino Library with 10 examples, and you can quickly explore the many featu...
SparkFun Pro Micro - RP2350
The SparkFun RP2350 Pro Micro provides a powerful development platform in SparkFun's compact Pro Micro form factor, built around the RP2350 from the Raspberry Pi Foundation. This board uses the updated Pro Micro form factor. It includes a USB-C connector, Qwiic connector, WS2812B addressable RGB ...
SparkFun Pro nRF52840 Mini - Bluetooth Development Board
The SparkFun Pro nRF52840 Mini is a breakout and development board for Nordic Semiconductor’s nRF52840 – a powerful combination of ARM Cortex-M4 CPU and 2.4GHz Bluetooth radio. With the nRF52840 at the heart of your project, you’ll be presented with a seemingly endless list of project-possibiliti...
SparkFun Pro RF - LoRa, 915MHz (SAMD21)
The SparkFun Pro RF is a LoRa®-enabled wireless board that marries a SAMD21 and a long-range RFM95W to make a compact and easy-to-use IoT Arduino board. With its fast MCU and excellent point to point data transmission in the 915MHz ISM band with LoRa Capabilities, the Pro RF is a great choice for...
SparkFun ProtoShield Kit
The SparkFun ProtoShield Kit lets you customize your own Arduino shield using whatever circuit you can come up with and then test it to make sure everything is working the way it should! The SparkFun ProtoShield Kit is based off the Arduino R3’s footprint that allows you to easily incorporate it ...
