All Products

SKU: AF-562 · MPN: 562

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-poin...

SKU: AF-4361 · MPN: 4361

Pipe audio in or out of your project with this very handy panel mount audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jack is inserted. You can use any 3.5mm audio cable with this jack.Each jack comes ...

SKU: AF-3692 · MPN: 3692

What is this TRS bit? Turtle Rock Studios? Transmission Raman Spectroscopy? Not quite, more like Tip-Ring-Sleeve. This nifty, gold-plated connector is known by many names, phone plug, phone jack, headphone jack, jack plug, etc. Used to transmit stereo audio signals, these connectors are...

SKU: AF-1789 · MPN: 1789

This 1K potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 1K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-poin...

SKU: AF-3691 · MPN: 3691

You've done such a great job making your own electronic control panel that the last thing you need are those wires to get pulled out and frizzy. These fancy Panel-Mount Banana Jacks look good and work well. They will snugly hold onto any 4mm banana plug or cable, and have a c...

SKU: AF-4056 · MPN: 4056

This panel mount cable will allow you to enclose a device that has a USB Micro B port, and also converts it to a modern USB C connector at the same time. Perfect for placing your project in a secure box! One end is a USB Micro B plug connector, and other is a USB C socket with special over-moldin...

SKU: AF-4053 · MPN: 4053

This panel mount cable will allow you to enclose a device that has a USB A port, and also converts it to a modern USB C connector at the same time. Perfect for placing your project in a secure box! One end is a USB Type A plug connector, and other is a USB C socket with special over-molding.The s...

SKU: AF-909 · MPN: 909

This handy Ethernet extension cable will make it easy for you to enclose a device that has an Ethernet port. We think this would be most useful when putting a Beagle Bone, Raspberry Pi, Arduino Ethernet into a box.The jack half has two mounting 'ears' with 4-40 screws installed, 1" inch / 25mm ap...

SKU: PI-CAB0903

A 50 cm panel mount HDMI extension cable for exposing an HDMI port on the outside of an enclosure or project box. One end features a panel-mount HDMI female socket with mounting holes, while the other end is a standard HDMI male connector. Specifications Connector (Panel Side) – HDMI female wi...

SKU: PI-CAB0906

Need to expose HDMI, Ethernet, or USB to the outside of your project/enclosure? These lovely little 50cm panel mount extension cables are just the job!Each cable comes with one end in panel mount format so that you can securely fix it to a flat surface and expose a port externally. Great for...

SKU: AF-3258 · MPN: 3258

Check out this handy MicroUSB extension cable, which will make it easy for you to enclose a device that has a B type (micro USB host) port. Great if you need to extend the USB port for your Raspberry Pi, Arduino, Feather or really anything development board.This Micro-B male/female extension...

SKU: AF-3318 · MPN: 3318

Check out this handy USB extension cable, which will make it easy for you to enclose a device that has a Mini-B USB type port. We think this would be most handy when putting a Teensy, FTDI friend, USB LiPo charger, BeagleBone, or any other Mini-B device into a box!This Mini-B male/female extensio...

SKU: AF-978 · MPN: 978

This panel mount extension cable will allow you to extend an HDMI connection and secure it to an enclosure. Perfect for placing your Raspberry Pi in a secure box. Two #4-40 screws are used to attach the female socket end, 26.9mm apart. Two hex-body standoff-screws are included as shown above and ...

SKU: AF-3121 · MPN: 3121

Make your own custom HDMI input or HDMI interface with ease, using this HDMI Socket Breakout. You get a nice solid PCB with an HDMI socket that you can solder to assemble your own wiring jigs. You can add in some terminal blocks to make the wiring easier, or check out the HDMI Socket...

SKU: AF-3120 · MPN: 3120

Make your own custom HDMI input or HDMI interface with ease, using this HDMI Socket to Terminal Block Breakout. You get a nice solid PCB with an HDMI socket and two strips of terminal blocks that you can use with stranded or solid core wire to assemble your own wiring jigs. We recommend this...

SKU: AF-5721

We've lost count of how many times we've tried to mount a camera module onto a panel or enclosure but struggled to drill the very small M2 holes right at the edge of the camera board, and don't even mention trying to get a nice clean cut-out for the lens!Mounting these tiny yet awesome cameras on...

SKU: AF-1729 · MPN: 1729

This panel-mount RCA cable provides a clean, permanent composite video or audio connection for enclosures and project boxes. Two RCA connectors (one panel-mount, one plug) are joined by a 264 mm (10.4″) cable, with two mounting screws spaced 20 mm apart for secure panel installation. Ideal for c...

SKU: AF-3395 · MPN: 3395

This Panel Mount Right Angle 10K Linear Potentiometer w/ On-Off Switch is a two-in-one, with both a breadboard-friendly potentiometer and a switch. For the potentiometer-half, you've got a standard linear taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not s...

SKU: AF-3319 · MPN: 3319

Make your next audio input/output project in a box with this handy Panel Mount Stereo Audio Extension Cable - 1/8" / 3.5mm. OK its quite a mouthful, but its pretty simple: that headphone or microphone jack you know and love? (OK everyone but you, Tim Cook!) Now you can attach it onto a bo...

SKU: SF-CAB-15463

This panel mount USB-B (female) to micro-B (male) cable enables you to more easily enclose a project that contains a USB micro-B port. The cable is 6" in length and includes two 14mm M3 screws compatible with the cable's 3mm panel mount holes, spaced 28.5mm apart.