All Products

SKU: EC-WRN13569N

This is a MiFare Classic keychain fob - often used for electronic locks or customer identification. The tag contains a NXP S50 chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away. Can be used with NFC Shield.Specification 1 KiloByte (8 KiloBit) non-...

SKU: DF-FIT0314

NFC Tag (13.56MHz) is widely used in electronic locks or customer identification as well as other systems where a small and easy to carry tag is desired.The tag contains a NXP S50 chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away. This Mifare-...

SKU: SF-SEN-21219

The 22.86 x 22.86mm Nicla Voice allows for easy implementation of always-on speech recognition on the edge, because it integrates Syntiant’s powerful NDP120 Neural Decision processor to run multiple AI algorithms, leveraging bio-inspired, advanced machine learning to automate complex tasks. Ni...

SKU: DF-SEN0338

A high-performance night vision camera module for Raspberry Pi, built around the Sony IMX327 STARVIS sensor. Designed for excellent low-light imaging without infrared fill light, this 2MP module delivers 1080p video at 30fps with built-in ISP, 2D/3D noise reduction, and anti-fog capabilities. Co...

SKU: PI-CAM008

Light up the night with this night vision camera module with infra-red LEDs, for Raspberry Pi! Available with ether a standard (70°) or a wide-angle (160°) lens, this camera has IR LEDs that allow the camera to see in the dark without producing visible light. The camera itsel...

SKU: LB-LS3580

The Night Vision Fisheye Camera 5MP OV5647 is a high-quality camera that offers a 95-degree focal adjustment for clear, precise images. It also features night vision capabilities for clear images even in low-light conditions. This camera is perfect for capturing detailed images and videos, ...

SKU: AF-940

You made an "Internet of Things" project! Adafruit offers a fun and exciting stickers to celebrate achievement for electronics, science and engineering. We believe everyone should be able to be rewarded for learning a useful skill, a sticker is just one of the many ways to show and share.Th...

SKU: SF-TOL-29532 · MPN: TOL-29532

This pre-fluxed copper desoldering braid is made for removing solder from joints, pads and small mistakes like solder bridges. Place it over the solder, heat it with your soldering iron, and the activated flux plus the braid’s capillary action draws molten solder into the wick.It is handy for rew...

SKU: SF-TOL-29533 · MPN: TOL-29533

This desoldering wick is a pre-fluxed copper braid for removing solder from joints, fixing excess solder, and cleaning up solder bridges. It is a handy bench consumable for rework, repairs, and swapping components on PCBs.To use it, place the braid over the solder joint and apply your soldering i...

SKU: LB-LR0128

Material: Experimental Board + Mixed Alloy Color: Black Chip Module: CP2102 Working Temperature: -40 ℃ ~ +125 ℃ Power Input: 4.5V ~ 9V (10VMAX), USB-powered Drive Type: Dual high-power H-bridge driver Current: continuous transmission ≈70mA (200mA MAX) Standby: <200uA Size: (L)X(W)4.8X2.5cm/1.8...

SKU: EC-DPO02102N

The NodeMCU R2 is a Wi-Fi development board based on the ESP8266 (ESP-12E module), featuring a CP2102 USB-to-UART bridge for reliable programming and debugging. It integrates GPIO, PWM, I2C, 1-Wire, and ADC on a single breadboard-friendly board, and can be programmed with the Arduino IDE or NodeM...

SKU: EC-DPO28090B

The NodeMCU V2 is a Wi-Fi development board based on the ESP8266 (ESP-12E module) with an on-board PCB antenna and USB programming interface. It supports 802.11 b/g/n wireless networking and can operate in STA, AP, or STA+AP modes with a built-in TCP/IP stack supporting up to 5 simultaneous TCP c...

SKU: JU-R-E97

You understand the 'slings and arrows of outrageous fortune', that's why we made this lapel pin: As a little reminder that the slings and arrows are the point of the whole thing. This pin is for those who've run out of fucks to give, and are now just along for the marvelous and thrilling ride... ...

SKU: PR-PIM356

Make your micro:bit sing with noise:bit! It's a tiny speaker&nbsp;that packs a fair bit of punch, and it's&nbsp;perfect for&nbsp;BLEEPS and BLOOPS! Just slot in your micro:bit,&nbsp;and use the sound generation blocks and code in Microsoft MakeCode and MicroPython to generate&nbsp;tones, sound...

SKU: SF-TOL-14793

The Nomad Flip Jig is a handy accessory for your Nomad 883 Pro that allows you to cut both sides of a part while maintaining perfect alignment. Each one of these jigs is precision machined to mount to the Nomad’s table and uses the CNC’s built-in machine calibration to make it easy to locate whil...

SKU: SF-TOL-14792

This Low Profile Vise provides you with a compact workholding accessory for the Nomad 883 Pro. Each one of these vises are made from scratch, in-house at Carbide 3D, and includes everything you need to attach it to your Nomad. The With the Low Profile Vise you will be able to miniature and small ...

SKU: SF-TOL-14794

If you need more ways to hold material in your Nomad, this Threaded Table provides you with plenty of connection points. Each Nomad Threaded Table is approximately 8in by 8in (~203mm by ~203mm) and ½" (12.7mm) thick and contains 72 M6x1 threaded holes. With as many connection points that the thre...

SKU: DF-SEN0368

A non-contact capacitive liquid level sensor that detects whether liquid is present inside a non-metallic container or pipe without direct contact with the fluid. It works by measuring changes in capacitance through the container wall, making it suitable for corrosive liquids, strong acids, alkal...

SKU: SF-SEN-11005

This non-invasive current sensor (also known as a split-core current transformer) clamps around the supply line of an electrical load to measure how much current is flowing through it. The sensor acts as an inductor, responding to the magnetic field around a current-carrying conductor, and output...

SKU: AF-5731

Our favorite food when hacking on code or electronics is a hot bowl of noodles - and around NYC these are often called 'noods'! What we've got here are flexible LED noodles in different lengths and colors. All are not good for eatin' but they are good for cool lighting effects These are often ...