DFRobot
Gravity: N20 Micro Metal Gear Motor with Integrated Drive (3V-6V, 1:150/133RPM)
·
The Gravity N20 is a compact all-metal gear motor with an integrated drive chip that simplifies motor control to a single PWM signal. Operating on 3–6 V, it ...
Get notified when back in stock
The Gravity N20 is a compact all-metal gear motor with an integrated drive chip that simplifies motor control to a single PWM signal. Operating on 3–6 V, it uses a PPM servo-style control method — forward, stop, and reverse are set by pulse width — eliminating the need for a separate motor driver.
The PH2.0-3P connector follows the Gravity pin standard for plug-and-play connection to DFRobot controllers and Arduino boards. With a 150:1 gear ratio and 133 RPM no-load output, it delivers reliable torque in a package weighing just 10 g.
Key Features
- Integrated Drive Chip – Single PWM signal controls speed and direction, no separate driver needed
- All-Metal Gearbox – 150:1 reduction ratio for reliable torque output
- PPM Servo Control – Forward (500–1400 µs), stop (1400–1600 µs), reverse (1600–2500 µs)
- Low Standby Power – Less than 1 mA static current when no control signal is present
- Gravity Connector – PH2.0-3P interface for easy plug-in connection
- Compact Size – 40 × 12 × 20 mm, weighing only 10 g
Specifications
- Operating Voltage – 3–6 V
- Rated Voltage – 6 V
- No-Load Current – 50 mA (at 6 V)
- Static Current – <1 mA (no signal)
- Stall Current – 640 mA
- Motor Speed (Unreduced) – 20,000 RPM
- Gear Ratio – 150:1
- No-Load Output Speed – 133 RPM
- Stall Torque – 1.0 kg·cm
- PPM Signal Resolution – 1 µs
- PPM Pulse Width Range – 500–2500 µs
- PWM Drive Frequency – 500 Hz
- Dimensions – 40 × 12 × 20 mm
- Weight – 10 g
Ideal For
- Robotics and mechanical motion control
- Valve and door lock actuators
- Arduino and microcontroller projects
- Compact motorised mechanisms
Package Contents
- 1× N20 Motor with Integrated Drive (133 RPM, 1:150)
- 1× Gravity 3-Pin Digital Sensor Cable
Find this product in
Brands
Robotics & Motion
Supplier page — dfrobot.com
Supplier Description · 603.4 KB · Click any page to view full size
DFR1114 gravity integrated drive n20 motor dimension 1.0
Mechanical Drawings · 36.5 KB · Click any page to view full size
You might also like
Customers who bought this also bought
Jargon buster
Plain-language definitions for the technical terms in the product description.
- Gravity
- Gravity is DFRobot’s plug-in connector system for sensors, motors and modules, using standard cables to reduce loose jumper wiring. It matters because Gravity-compatible parts can connect directly to these ports, while non-Gravity parts may need adapters or manual wiring.
- kg·cm
- A torque unit often used for hobby servos, meaning how many kilograms of force the servo can hold at a 1 cm arm length. A higher kg·cm rating means the servo can move or hold heavier loads, but power supply current needs may also increase.
- microcontroller
- A microcontroller is a small computer on a single chip that runs a stored program and controls connected inputs and outputs such as buttons, sensors, displays and communication interfaces. In a device built around one, it is the part that executes the code and coordinates the device's behaviour.
- motor driver
- An electronic circuit that lets a low-power controller switch and control a motor that needs more current than the controller pins can safely provide. Checking motor driver support matters because pumps and motors usually cannot be connected directly to a microcontroller output.
- ppm
- ppm means parts per million, a common way to express very small gas concentrations in air. For CO₂ sensors, the ppm range tells you what levels the sensor can measure, such as normal indoor air through to poorly ventilated spaces.
- Pulse width range
- The span of control pulse lengths a servo understands, usually measured in microseconds. Matching this range in your code affects how far the servo moves and helps avoid commanding positions outside its intended travel.
- PWM
- Pulse Width Modulation is a way for a digital pin to simulate variable output power by switching on and off very quickly. It matters for controlling things like LED brightness, motor speed, or servo-style signals from a microcontroller pin.
- servo
- A servo is a motor with built-in position control, usually told to move to a specific angle by a control signal. It matters when you need repeatable movement, such as steering, arms, flaps, or linkages, rather than continuous spinning.
- Stall torque
- The maximum twisting force a servo can produce when its output is held still and cannot move. It helps you judge whether the servo is strong enough for a robot joint, steering linkage, or other load.
- Torque
- A twisting force that causes something to rotate, usually measured in newton-metres or kilogram-centimetres. It matters when choosing motors, servos, gears, and tools because higher torque is needed to lift heavier loads, turn larger wheels, or move mechanisms without stalling.