DFRobot
ECell: Breadboard-Plugin Components Pack
All Products
Circuitry Accessories
New Arrivals
Capacitors
Circuitry & IOT
Prototyping
DFRobot
Digital Technologies
Education
Components
Resistors
Prototyping & Wiring
$34.90
|
In stock at supplier
INTRODUCTION Breadboard-Plugin Components Pack is a new kit designed for breadboard experiment. It provides many kinds of compo...
Get notified when back in stock
Estimated Delivery
Arrives
Disclaimer
Secure checkout
INTRODUCTION
Breadboard-Plugin Components Pack is a new kit designed for breadboard experiment. It provides many kinds of components, such as resistors, capacitors, diodes, transistor .etc. The module pins are using gold-plating technology, solid and durable. It could be plugged on the breadboard directly. easy, reliable and reusable.
This innovative approach will solve the following issues caused by using DIP type of components:- Hard to read the value (Resistor color codes)
- Severe deformations of the pin after used, non-reusable, not environment-friendly
- The pin diameter is too thin or too thick, poor match with the breadboard hole
- Confused the order of transistor "e", "b", "c" pins
- Usage problem: Most of sensors and actuators require 3 interfaces: Signal/VCC/GND, you have to use the jumper wire for the connection, messy and unreliable.
FEATURES
- Easy to Recognize : Resistance value, capacitance values, positive/negative polaron and pin functions are marked clearly.
- Easy to Learn : The circuit symbol is clearly visible, directly match the circuit diagram
- Easy to Use : Direct-plug pin
- Easy to Plug/unplug : The 0.64mm diametral pin matches the breadboard hole perfectly
- High-Reliability : ENIG technology, the circuit connection is reliable and durable
- Environment-Friendly : Reusable and Environment-friendly
SPECIFICATION
- Resistor: 220R, 1K, 4.7K, 10K
- Capacitor: 22pF@50V, 100nF(0.1uF)@50V, 47uF@10V
- LED: Red, Yellow, Blue, Green
- Diode: If=1A, Vfm=0.7V, Vr=40V
- Transistor-NPN: Vceo=45V, Ic=500mA, hFE=400
- Transistor-PNP: Vceo=-45V, Ic=-500mA, hFE=400
DOCUMENTS
SHIPPING LIST
- Resistor 220R x4
- Resistor 1K x4
- Resistor 4.7K x4
- Resistor 10K x4
- Capacitor 22pF x2
- Capacitor 100nF x2
- Capacitor 47uF x2
- LED--R x2
- LED--Y x2
- LED--B x2
- LED--G x2
- Diode x4
- NPN transistor x2
- PNP transistor x2
- Breadboard PluginConnector x2
Jargon buster
Plain-language definitions for the technical terms used above.
- capacitance
- Capacitance is the amount of electrical charge a capacitor can store, usually measured in farads such as uF. Choosing the right capacitance value matters because it affects how well a circuit filters power, handles timing, or stores short bursts of energy.
- GND
- GND is the ground or reference connection (0 V) for a circuit. When connecting two devices together, their grounds must be joined so both agree on what counts as a low or high signal.
- LED
- A light-emitting diode (LED) is a small electronic component that emits light when current flows through it in the correct direction. Because it only conducts one way, its polarity matters, and a through-hole LED must be soldered the correct way around to light up.
- VCC
- VCC is the positive power-supply connection on a chip or module. Connecting it to the correct supply voltage is needed for the part to power on and helps avoid damaging the electronics.
Find this product in
Components
Related Tutorials
Free guides on learn.littlebird.com.au
