Adafruit
Adafruit DotStar LED Strip - APA102 Cool White - 60 LED/m [~6000K] 1m
The Adafruit DotStar APA102 Cool White LED Strip (60 LED/m, ~6000K) uses the same integrated DotStar driver as the RGB strips but with dedicated cool white p...
Get notified when back in stock
The Adafruit DotStar APA102 Cool White LED Strip (60 LED/m, ~6000K) uses the same integrated DotStar driver as the RGB strips but with dedicated cool white phosphor LEDs. The result is an incredibly bright, consistent white light — far superior to mixing RGB to approximate white.
Controlled via a 2-wire SPI interface at up to 32 MHz, each LED features 24-bit PWM brightness control at 20 KHz for smooth, flicker-free dimming. No timing-critical code is required, making these strips compatible with any microcontroller or microprocessor. This is the 60 LED/m density on white flex PCB, sold from 4-metre reels.
Key Features
- Cool White ~6000K – Dedicated white phosphor LEDs for true, consistent white light
- SPI Interface – 2-wire (clock + data) protocol works with any processor speed
- 24-Bit Brightness Control – High-frequency 20 KHz PWM for smooth, flicker-free dimming
- Up to 32 MHz Data Rate – Hardware SPI supported but not required
- Weatherproof Sheathing – Flexible PCB with protective coating
- Cuttable – Cut lines every 1 LED, solder to 0.1" copper pads
- Chainable – Connect strips together for longer runs
- 4-Pin JST SM Connectors – Included on each end of full reels
Also Available
- DotStar Cool White 30 LED/m (~6000K)
- DotStar Cool White 144 LED/m (~6000K)
- DotStar Warm White 30 LED/m (~3000K)
- DotStar Warm White 60 LED/m (~3000K)
- DotStar Warm White 144 LED/m (~3000K)
Ideal For
- Under-cabinet and task lighting
- Architectural and display illumination
- Photography and video lighting rigs
- Smart home lighting with programmable dimming
Package Contents
- 1× DotStar Cool White LED strip – 60 LED/m, ~6000K, 1 metre, white flex PCB
Jargon buster
Plain-language definitions for the technical terms used above.
- DC
- DC means direct current, where electricity flows in one constant direction, as supplied by batteries, USB ports and many plug-pack power supplies. When a product specifies DC, it runs from a DC supply rather than mains AC, so you need to provide the correct voltage and polarity.
- LED
- A light-emitting diode (LED) is a small electronic component that emits light when current flows through it in the correct direction. Because it only conducts one way, its polarity matters, and a through-hole LED must be soldered the correct way around to light up.
- microcontroller
- A microcontroller is a small computer on a single chip that runs a stored program and controls connected inputs and outputs such as buttons, sensors, displays and communication interfaces. In a device built around one, it is the part that executes the code and coordinates the device's behaviour.
- PCB
- A printed circuit board (PCB) is a board, usually rigid, with etched copper tracks that connect electronic components together without loose wiring. Components are mounted on the board and signals route between them through the copper layout.
- PWM
- Pulse Width Modulation is a way for a digital pin to simulate variable output power by switching on and off very quickly. It matters for controlling things like LED brightness, motor speed, or servo-style signals from a microcontroller pin.
- RGB
- Short for red, green and blue, the three primary colours of light that are mixed in varying amounts to make a wide range of colours. In electronics RGB can refer to an LED or pixel that blends these three colours, or to a colour signal or interface that carries separate red, green and blue channels.
- SPI
- A fast serial communication bus often used for displays, memory cards, and sensors. It matters because SPI devices need specific pins for clock and data, plus a separate chip-select line for each device.
Find this product in
Brands
Related Tutorials
Free guides on learn.littlebird.com.au
