Wearable Tech & E-textiles

SKU: LB-FABRIC | Brand: Little Bird

A 20-metre roll of self-adhesive conductive fabric tape with copper and nickel coating on a high-strength polyester substrate. This flexible shielding tape is designed for EMI/RFI suppression in electronics, providing...

SKU: LB-LR0281-5-P | Brand: Little Bird

This 5m length of EL wire (electroluminescent wire) is a flexible wire coated with phosphor which glows blue when applied with the appropriate voltage. Whilst EL wire looks similar to a thin neon tube, the wire is in ...

SKU: SF-DEV-14014 | Brand: SparkFun

This is a simple pack of five Yellow LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up.LilyPad is a wearable e-...

SKU: M5-U029 | Brand: Little Bird

Description HEART is build with MAX30100.. MAX30100 is a complete pulse oximetry and heartrate sensor system solution designed for the demanding requirements of wearable devices. The MAX30100 provides ...

SKU: AF-1167 | Brand: Adafruit

This silver-plated knit conductive fabric is a flexible, stretchable material for e-textile and soft circuit applications. With a resistance of less than 1 ohm per foot in any direction, it conducts electricity reliab...

SKU: AF-4300 | Brand: Adafruit

The Adafruit HalloWing M4 Express is a skull-shaped development board powered by the ATSAMD51G18 — a 120 MHz Cortex M4 processor with 512 KB Flash and 192 KB RAM. Featuring a 1.54" IPS TFT display (240×240 pixels), a ...

SKU: AF-4182 | Brand: Adafruit

A 3.5 mm mono audio jack cable with alligator clips on the other end, making it easy to clip onto development boards like the BBC micro:bit or Adafruit Circuit Playground. Also compatible with AT (accessibility techno...

SKU: LB-LR0347A | Brand: Little Bird

This E-Textiles  Coin Cell Battery Holder has a small slide switch installed on the board, in-line with the power so you can shut off your project and save batteries. This slide switch is the same as is found on ...

SKU: PI-PSA001 | Brand: Pimoroni

The Pulse Sensor Amped is a plug-and-play heart-rate sensor for Arduino. It detects pulse by measuring changes in reflected light as blood pumps through your tissues, providing a real-time analogue signal that fluctua...

SKU: PL-1696 | Brand: Pololu

This force-sensing resistor (FSR) from Interlink Electronics is a passive component that exhibits a decrease in resistance when there is an increase in the force applied to the 0.58″-diameter (1.5 cm) active area...

SKU: AF-615 | Brand: Adafruit

This gold-eye sharps needle set is perfect for hand-sewing with conductive thread and wearable electronics parts. The pack includes 20 needles in sizes #3 to #9, giving you the right needle for any e-textiles or gener...

SKU: AF-2328 | Brand: Adafruit

Adafruit DotStar LED strips use 2-wire SPI instead of the single-wire protocol used by NeoPixels, allowing much faster data rates (up to 32 MHz) and a 20 KHz PWM refresh rate. This makes DotStars ideal for persistence...

SKU: LW-TEK6 | Brand: Little Bird

Teknikio Blue star-shaped sewable LED board.  Product Details• Add light up LED Stars to your crafts• LED light is blue• Pack Includes 4x LED Stars• Recommended Age 8+

SKU: AF-2239 | Brand: Adafruit

The Adafruit DotStar Digital LED Strip (60 LED/m, black flex PCB) delivers superior performance over traditional NeoPixels with its 2-wire SPI interface. Push data at up to 32 MHz clock speed with no critical timing r...

SKU: SF-KIT-13927 | Brand: SparkFun

The LilyPad Sewable Electronics Kit is an introduction to the world of e-textiles and electronic sewing. Through a series of guided projects, you'll learn to sew basic circuits, light up LEDs, control them with button...

SKU: SF-DEV-13902 | Brand: SparkFun

This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up.LilyPad is a wearable e-t...

SKU: AF-653 | Brand: Adafruit

This sewable CR2032 battery holder makes it easy to add power to wearable electronics projects. Two small 1mm holes in the metal connection tabs are perfectly sized for a #5 or smaller needle to pass through, so you c...

SKU: AF-4429 | Brand: Adafruit

This 13.56 MHz RFID/NFC sewable button uses an NTAG213 chip in a compact 24 mm laundry-tag form factor. It can be sewn into garments, attached to equipment, or embedded in projects for contactless identification, data...

SKU: KI-2715 | Brand: Kitronik

A starter kit for e-textiles and wearable electronics from Kitronik's Electro-Fashion range. This Discovery Pack includes a curated selection of sewable components — LEDs, switches, coin cell holders, conductive threa...

SKU: PI-TEK004 | Brand: Pimoroni

A four pack of sewable, heart-shaped bright pink LEDs. The voltage (and hence current) supplied from LIR2032 rechargeable coin cell batteries may damage the Teknikio LED boards, so please ONLY USE CR...