Standoffs & Screws

These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up ...

This 12 position screw terminal block provides a simple way to connect wires to a single connection point. These blocks allow wires to be screwed t...

We understand that small part tend to get lost or damaged easily. These Panel Mount Nuts are handy replacement units that fit most of our panel mou...

Keep your components separated with this 25-pack of 12mm-long (0.47") nylon spacers. These spacers have an outer diameter (OD) of 5 mm (0.20") and ...

Keep your components separated with this 25-pack of 10mm-long (0.39") nylon spacers. These spacers have an outer diameter (OD) of 5 mm (0.20") and ...

This #4-40, pan-head screw is 1 1/4″ (1.25″) long. It is made from steel, is zinc-plated, and comes in packs of 25.

This #4-40, pan-head screw is 1/2″ (0.5″) long. It is made from steel, is zinc-plated, and comes in packs of 25.

Metal long standoffs: 1" long x ¼" OD. Used to get your proto board up off the table. #4-40 thread. Fits most development boards with available hol...

Metal short standoffs: 3/8" long x ¼"OD. Used to get your proto board up off the table. #4-40 thread. Fits all development boards with available ho...

This #2-56, pan-head screw is 1 1/4″ (1.25″) long. It is made from steel, is zinc-plated, and comes in packs of 25.

A button is a button, and a switch is a switch, but this LED illuminated arcade buttons is in a class of its own. Its the same size as a 'standard'...

This #4-40, pan-head screw is 1/4″ (0.25″) long. It is made from steel, is zinc-plated, and comes in packs of 25.

This #2-56, pan-head screw is 7/16″ long (0.4375″). It is made from steel, is zinc-plated, and comes in packs of 25.

This #2-56, pan-head screw is 1/4″ (0.25″) long. It is made from steel, is zinc-plated, and comes in packs of 25.

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pi...

INTRODUCTION This part is belt tensioner, which could adjust the tensity of the belt. Compatible with both the Ove...

These nylon standoffs are ¾" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off t...

Metal Hex Male/Female standoffs. #4-40 thread with 3/8" shank and 3/16" thread length. Can be stacked to create any length. Pack of 10

These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off...

Pack of 200 steel screws. Specifications Fastener Type Screw ...

There are your standard Philips-head 4-40 screws. They are ¼" long and come in packs of ten. This is the screw size we use in most of the holes for...

Standard Philips-head 4-40 screws. They are ½" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout b...

Standard Philips-head 4-40 screws. They are 1" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout b...

These are very handy. They are simple angle brackets with one threaded and unthreaded hole. Use them for connecting PCBs at 90 degree angles, mount...