Sensors

SKU: AF-1782 | Brand: Adafruit

This I2C digital temperature sensor is one of the more accurate/precise we've ever seen, with a typical accuracy of ±0.25°C over the sensor's -40°C to +125°C range and precision of +0.0625°C. They work great with any ...

SKU: AF-1849 | Brand: Adafruit

Get started with wearable electronics using the Adafruit Gemma Sensor Starter Pack. This all-in-one kit includes a GEMMA V2 board, sewable RGB NeoPixels, multiple sensors, a rechargeable battery with charger, and ever...

SKU: DF-SEN0014 | Brand: DFRobot

The Sharp distance sensors are a popular choice for many projects that require accurate distance measurements. This IR sensor is more economical than sonar rangefinders, yet it provides much better performance than o...

SKU: AF-2461 | Brand: Adafruit

Wow that's a tiny GPS antenna! This passive antenna is only 15mm x 15mm x 6.8mm in size, with a 50mm long uFL cable. Great for when you want to keep things small. Comes with a standard uFL connector on the end. Pe...

SKU: DF-SEN0227 | Brand: DFRobot

This SHT20 I2C temperature & humidity sensor is equipped with waterproof probe. It comes with the 4C CMOSens® SHT20 temperature & humidity sensor chip and the probe has gone through dual waterproof protection test...

SKU: DF-DFR0126 | Brand: DFRobot

This Audio Analyzer module features the MSGEQ7 graphic equalizer display filter.It will give your arduino ears. Sound is broken down into seven frequency bands and the peak level for each band can be read. The seven ...

SKU: DF-SEN0097 | Brand: DFRobot

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier ...

SKU: DF-SEN0104 | Brand: DFRobot

This is a cool touch sensor from DFRobot. You can hook it up to the IO Expansion shield (for arduino) directly. It includes a metallic tape with a sticky side. This make it possible for you to place your sensors...

SKU: AF-2738 | Brand: Adafruit

Control the same hardware as used in space...build your very own Astro Pi with the new Raspberry Pi Sense HAT! The Raspberry Pi Sense HAT is attached on top of the Raspberry Pi via the 40 GPIO pins to create an ‘As...

SKU: SF-SEN-09299 | Brand: SparkFun

The GP1A57HRJ00F is a slotted optical sensor (photo interrupter) with an infrared emitter on one upright and a shielded infrared detector on the other. When an object passes through the 10 mm gap between the uprights,...

SKU: SF-SEN-09198 | Brand: SparkFun

The Minisense 100 from Measurement Specialties is a low-cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. Useful for detecting vibration and ‘tap’ inputs from a user....

SKU: SF-SEN-09197 | Brand: SparkFun

A flexible piezo vibration sensor from Measurement Specialties, commonly used for detecting flex, touch, vibration, and shock. The PVDF polymer film generates a small AC voltage (up to ±90 V) when it moves, which can ...

SKU: DF-SEN0132 | Brand: DFRobot

INTRODUCTION This is an Arduino Carbon Monoxide Sensor. It uses MQ7 probe to detect Carbon Monoxide (CO) concentrations in the air from 20 to 2000ppm. The sensitivity ca...

SKU: DF-FIT0227 | Brand: DFRobot

The MQ7 is a simple-to-use Carbon Monoxide (CO) sensor suitable for detecting CO concentrations in the air. It offers a wide detection range from 20 to 2000 ppm, making it ideal for safety monitoring and air quality p...

SKU: DF-SEN0138-R | Brand: DFRobot

A miniature snap-action switch, also trademarked and frequently known as a micro switch, is an electric switch that is actuated by very little physical force.Micro switches are very widely used; among their appl...

SKU: SF-BOB-08891 | Brand: SparkFun

This breakout board provides a convenient PCB adapter for MQ-series gas sensors (MQ-3, MQ-4, MQ-6, MQ-7, and MQ-8). It converts the sensor's oversized, oddly-spaced pins into a standard breakout format that's easy to ...

SKU: DF-SEN0139 | Brand: DFRobot

This is a K type Thermocouple (Temperature sensor) which is very popular for 3D printers such as Ultimaker and Makerbot. You can hardly damage them or mishandle them. You just need an additional IC (Like an AD595) ...

SKU: SF-DEV-08777 | Brand: SparkFun

Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to dig...

SKU: SF-SEN-08712 | Brand: SparkFun

This is a piezoresistive force sensor from Tekscan. The harder you press, the lower the sensor’s resistance. Pressing hard, the resistance changes from infinite to ~300k. The sensor itself is thin and flexible, but th...

SKU: SF-SEN-08681 | Brand: SparkFun

These are very thin variable potentiometers. By pressing down on various parts of the strip, the resistance linearly changes from 100Ohms to 10,000Ohms allowing the user to very accurately calculate the relative po...