Sensors

SKU: AF-3721 | Brand: Adafruit

The AM2320 is a low-cost digital temperature and humidity sensor with an I2C interface — a simpler alternative to the classic DHT11/DHT22 sensors that require timing-critical bit-bang protocols. With standard I2C comm...

SKU: SF-SEN-14349 | Brand: SparkFun

This is not your normal Passive Infrared (PIR) sensor! The SparkFun AK9753 Human Presence Sensor Breakout is a Qwiic-enabled, 4-channel Nondispersive Infrared (NDIR) sensor. Each channel has a different field of view...

SKU: SF-COM-08236 | Brand: SparkFun

This is a fully assembled simple breakout board for the surface mount 3-way switch. These switches are commonly found on handheld devices like MP3 players. This switch allows the user to navigate using up and down sel...

SKU: AF-1727 | Brand: Adafruit

The MAX31850K breakout board is a 1-Wire thermocouple amplifier with cold-junction compensation for K-type thermocouples. Unlike SPI-based amplifiers, the 1-Wire interface allows any number of thermocouple breakouts t...

SKU: AF-1032 | Brand: Adafruit

A gyroscope is a type of sensor that can sense twisting and turning motions. Often paired with an accelerometer, you can use these to do 3D motion capture and inertial measurement (that is - you can tell how an object...

SKU: DF-SEN0005 | Brand: DFRobot

This low cost SFR02 ultrasonic ranger has both I2C and Serial interfaces. New AutoTune algorithms intelligently back the minimum range right up to the transducer ringdown for the very best performance possible, aut...

SKU: DF-SEN0233 | Brand: DFRobot

A multifunction air quality monitor that measures particulate matter (PM2.5), formaldehyde concentration, temperature, and humidity. It uses laser scattering to detect suspended particles in the air, an electrochemica...

SKU: PL-2454 | Brand: Pololu

The QTR-L-1A reflectance sensor incorporates a right-angle infrared LED and a right-angle phototransistor in an inexpensive, tiny 0.35″ × 0.3″ module that can be mounted almost anywhere and is great for e...

SKU: SF-BOB-09322 | Brand: SparkFun

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>...

SKU: AF-466 | Brand: Adafruit

The VCNL4010 sensor is a nice way to add a small-distance proximity sensor to your microcontroller project. For longer distances (in the range of cm, you can use a SHARP IR distance sensor, but those are only good ...

SKU: DF-SEN0131 | Brand: DFRobot

INTRODUCTION This is an Arduino Propane Gas Sensor. It uses MQ6 probe to detect iso-butane, propane and liquefied petroleum gas (LPG). It is less sensitive with alcohol, cooking fumes an...

SKU: PL-1483 | Brand: Pololu

This semiconductor gas sensor detects the presence of Carbon Monoxide at concentrations from 10 to 1,000 ppm and combustible gas from 100 to 10,000 ppm. The sensor’s simple analog voltage interface requires ...

SKU: DF-SEN0140 | Brand: DFRobot

The DFRobot 10 DOF MEMS IMU Sensor combines four sensors on a single compact board — the ADXL345 accelerometer, ITG-3205 gyroscope, HMC5883L magnetometer, and BMP085 barometric pressure sensor. Together they provide 1...

SKU: SF-COM-08348 | Brand: SparkFun

The TEMT6000x01 is a compact ambient light sensor that operates as an NPN phototransistor. The more light that hits the sensor, the stronger the base bias, producing an analog output proportional to the ambient light ...

SKU: SF-SEN-12040 | Brand: SparkFun

The INA169 is a “high-side current monitor,” which means that you place a resistor (a “shunt resistor”) on the positive power rail and the INA169 measures the voltage drop across that resistor. The INA169 outputs a sm...

SKU: DF-FIT0319 | Brand: DFRobot

This is a photoelectric switch that is composed of emitter and receptor.The emitter consists of a laser diode,and the laser has the characteristics of high precision, good orientation etc.The receptor consists of a p...

SKU: SF-SEN-13963 | Brand: SparkFun

The SparkFun LIS3DH breakout is a low-power, three-axis accelerometer with 12-bit resolution, ideal for adding motion and orientation detection to your projects. It communicates over I2C or SPI and includes three addi...

SKU: PL-1268 | Brand: Pololu

The Pololu MinIMU-9 v2 is a compact (0.8″ × 0.5″) board that combines ST’s L3GD20 3-axis gyroscope and LSM303DLHC 3-axis accelerometer and 3-axis magnetometer to form an inertial measurement unit (IMU); we therefore r...

SKU: PL-1265 | Brand: Pololu

This board has been replaced by the newer MinIMU-9 v2 L3GD20 and LSM303DLHC carrier, which offers improved magnetic sensing resolution, a wider acceleration measurement range, and gyro measurements that are more resis...

SKU: SF-SEN-11859 | Brand: SparkFun

This is not your typical temperature sensor. The TMP006 Breakout can measure the temperature of an object without making contact with it. By using a thermopile to detect and absorb the infrared energy an object is emi...