Robotics & Motion

SKU: DF-SER0039 | Brand: DFRobot

A compact 9g micro servo with metal gears, delivering 1.8 kgf·cm of torque at 4.8V. The metal gear train provides significantly better durability than plastic versions, especially in robotics applications where the se...

SKU: LB-LS0112-60 | Brand: Little Bird

The JGA25-370 is a compact 12V DC gear motor with metal gears, delivering 60 RPM at 12V. The higher gear ratio provides increased torque at lower speed, making it well-suited for applications needing slow, controlled ...

SKU: LB-LR0149 | Brand: Little Bird

The EasyDriver is a simple stepper motor driver board based on the Allegro A3967 IC. It accepts a digital step/direction input (3.3 V or 5 V logic) and drives bi-polar stepper motors (4, 6, or 8 wire) at any voltage w...

SKU: MG-980-0529 | Brand: Little Bird

Speed into STEAM with this indi kit designed to engage kids ages 4+ in hours of exciting exploratory learning and play at home. Perfect forparents, grandparents, caretakers, or anyone looking to equip their young lear...

SKU: AF-4554 | Brand: Adafruit

The Adafruit TDK InvenSense ICM-20948 is a compact 9-DoF Inertial Measurement Unit that packs a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer into a single breakout board. It pairs InvenSense's MEMS ...

SKU: DF-ROB0153 | Brand: DFRobot

If you are gonna build a robotics project, then you need to check out this guy, Black Gladiator. He is an agile tracked robot chassis, low noise, and easy to control, which could be a good partner for your any tank-li...

SKU: AF-169 | Brand: Adafruit

Tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller. You can use any servo code, hardware or library to control these servos...

SKU: DF-DFR0429 | Brand: DFRobot

INTRODUCTION An ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the process of finding the right motor driver, connecti...

SKU: DF-MBT0021-EN-18650 | Brand: DFRobot

Maqueen Plus V2 is a STEAM educational robot platform for the micro:bit, made for classroom teaching, after-school projects and robot competitions. It builds on Maqueen Lite and earlier Maqueen Plus robots with a larg...

SKU: DF-ROB0148-EN-LB | Brand: DFRobot

This compact STEAM education robot is built around the Maqueen 4.2 core and is designed for children aged 8 and up. It arrives pre-assembled, with the motors, wheels, support wheel, housing and battery holder already ...

SKU: SF-SEN-14727 | Brand: SparkFun

This miniature straight bar load cell (sometimes called a strain gauge) can translate up to 100g of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that cha...

SKU: LB-LR0214-50 | Brand: Little Bird

The 42BYG is a NEMA 17 bipolar stepper motor with a shaft-reversed design, commonly used in 3D printers, CNC machines, and DIY motion-control projects. With a 1.8° step angle and 40 N·cm holding torque, it provides re...

SKU: DF-FIT0200 | Brand: DFRobot

This immersible pump can be used to water your plants, make a fountain or waterfall, even change your fish tank wter.It works quietly with the sound level under 30db. The pump has a filter inside as well as a suct...

SKU: SF-ROB-13302 | Brand: SparkFun

These are a pair of hobby gearmotors from DAGU. These gearmotors are the same ones recommended for use in the Shadow Chassis and offer a cheap and easy-to-use setup to get your wheels turning. Each Hobby Gearmotor als...

SKU: LB-LR0051 | Brand: Little Bird

A 4-channel relay module with opto-isolated inputs for safe, reliable switching of high-power loads. Each relay is rated for up to 10A at 250VAC or 30VDC, making it suitable for controlling lights, motors, heaters, an...

SKU: LB-LS5142-40 | Brand: Little Bird

The NEMA17 42BYGH40 Stepper Motor is a robust and reliable solution for precision motion control. With a body size of 42mm x 42mm and a length of 40mm, this stepper motor is widely used in 3D printers, CNC machines, a...

SKU: WS-25076 | Brand: Waveshare

The Waveshare UGV02 is a 6-wheel, 4WD off-road mobile robot chassis designed for robotics development and autonomous navigation projects. With flexible rubber tyres, independent suspension, and four driven wheels, it ...

SKU: EC-CDP03051C | Brand: Elecrow

The Arduino CNC Shield V3.51 by Protoneer turns an Arduino Uno into a 4-axis CNC controller. Compatible with GRBL 0.9 firmware, it accepts Pololu-style stepper drivers (sold separately) and supports up to 4 stepper mo...

SKU: DF-DFR0502 | Brand: DFRobot

Gravity IO Expansion Shield with Motor Driver is a new product designed for Arduino Boards. It combines IO Expansion Shield and DC Motor Driver Shield, equipped with Gravity sensor interface and...

SKU: AF-2448 | Brand: Adafruit

The Adafruit TB6612 Breakout is a compact dual H-bridge motor driver that can spin two DC motors bidirectionally, step one bipolar or unipolar stepper, or fire two solenoids — all at up to 1.2A continuous per channel ...