Prototyping & Wiring

SKU: DF-FIT0214 | Brand: DFRobot

This is a two-sided parts box for securely holding electronic components,screws,wires and any small parts in individual compartments. One side has 4 compartments and the other has 6. It's a great tool to keep your ...

SKU: AF-2739 | Brand: Adafruit

Make some beautiful colors with these diffused rectangular 2.5mm x 5mm RGB LEDs with separate red, green and blue LED chips inside! They make nice indicators, and they're fun to color-swirl! We like dif...

SKU: SF-BOB-08891 | Brand: SparkFun

This breakout board provides a convenient PCB adapter for MQ-series gas sensors (MQ-3, MQ-4, MQ-6, MQ-7, and MQ-8). It converts the sensor's oversized, oddly-spaced pins into a standard breakout format that's easy to ...

SKU: DF-FIT0223 | Brand: DFRobot

A medium-sized aluminium heat sink with pre-applied 3M 8810 thermal adhesive tape on the back. Simply peel off the blue protective film and stick it directly onto your IC or chip — no thermal paste or glue required. T...

SKU: SF-WRL-14131 | Brand: SparkFun

This is your solution when you absolutely, positively need to get the most out of an antenna for your next RFID project. This ultra high-frequency (UHF) RFID Antenna boasts a frequency range of 860-960 MHz with a g...

SKU: SF-CAB-14132 | Brand: SparkFun

This is a very simple 1m long TNC to RP-SMA cable. We like to use this cable to connect our ultra high-frequency RFID antennas to an equally powerful reader board. This cable is perfect for extending pre-existing c...

SKU: SF-PRT-08808 | Brand: SparkFun

This is a very simple but extremely handy, 1" square, single sided perf board. Standard 0.1" spacing with a 4-40 (3mm) hole for mounting. Every three holes are connected with a 20mil trace.  Package of 2

SKU: AF-2789 | Brand: Adafruit

The premise of this MicroUSB to 5.5/2.1mm DC Barrel Jack Adapter is simple. There's a MicroUSB plug on one end and a 5.5mm/2.1mm DC barrel jack with center positive polarity on the other. This allows you ...

SKU: DF-FIT0290 | Brand: DFRobot

This is a SOP8 to DIP8 Adapter Board. You can change the SOP8 to DIP8 packaging.So that You needn't to buy the DIP chips for prototyping specially.Just solder the SMD chips on the board and plug it into the bread b...

SKU: AF-2777 | Brand: Adafruit

This USB to DC booster cable has an integrated boost converter that steps up 5V USB power to 9V DC, output through a centre-positive 2.1 mm barrel jack. It's a convenient way to power 9V devices from any USB port — wh...

SKU: SF-SEN-08681 | Brand: SparkFun

These are very thin variable potentiometers. By pressing down on various parts of the strip, the resistance linearly changes from 100Ohms to 10,000Ohms allowing the user to very accurately calculate the relative po...

SKU: DF-FIT0294 | Brand: DFRobot

A 10-pack of M3 × 6mm low-profile hex head cap screws with matching nuts. The hex socket drive provides a more secure fastening than standard Phillips or slot-head screws, and the low-profile head sits flush for a cle...

SKU: DF-DFR0224 | Brand: DFRobot

The Arduino Screwless Terminal Shield breaks out all Arduino Uno-compatible header pins to spring-loaded push-in terminal blocks. Press the lever, insert your wire, and release — no screwdriver needed. The shield stac...

SKU: DF-FIT0273 | Brand: DFRobot

A 10-pack of M3 × 16mm low-profile hex head cap screws with matching nuts. The hex socket drive provides a more secure fastening than standard Phillips or slot-head screws, and the low-profile head sits flush for a cl...

SKU: SF-COM-08588 | Brand: SparkFun

This is a very common signal diode - 1N4148. Use this for signals up to 200mA of current. If you need a bunch of these, you can get good bulk discounts on Digikey, part # : 1N4148FS-ND Documents: Datasheet

SKU: SF-PRT-08535 | Brand: SparkFun

This 2×5 (10-pin) IDC ribbon cable with 2.54 mm pitch connectors is commonly used for AVR ISP programming and general-purpose communication between boards. The cable is 6 inches (approximately 15 cm) in length. Key F...

SKU: DF-FIT0295 | Brand: DFRobot

An assortment of 35 crystal oscillators covering 7 of the most commonly used frequencies. Keep them on hand for microcontroller projects, prototyping, and circuit experiments — no more hunting for the right crystal wh...

SKU: SF-PRT-08506 | Brand: SparkFun

A 2×5 (10-pin) shrouded box header on standard 0.1" (2.54 mm) pitch. The keyed shroud prevents reversed cable connections, making it ideal for programming headers, data buses, and other multi-pin interfaces. Key Feat...

SKU: SF-TOL-12033 | Brand: SparkFun

A parts kit for building or repairing an additional arm on the SparkFun Third Hand soldering helper. Includes alligator clips and the hardware needed to convert a coolant hose segment into a flexible helping hand. Id...

SKU: SF-COM-08184 | Brand: SparkFun

A compact 3-way surface-mount navigation switch commonly found in handheld devices like MP3 players. The switch provides up, down, and centre-press (select) actions in a single low-profile package — ideal for menu nav...