Prototyping & Wiring

SKU: DF-FIT0614 | Brand: DFRobot

Nowadays, LED strip is becoming more and more prevalent in our daily life. Sometimes, especially in festival days, we even feel that there are no more fun and excitement without it. How about getting a cool LED str...

SKU: KI-5625 | Brand: Kitronik

The ZIP Halo is a circular LED board for the BBC micro:bit featuring 24 individually addressable full-colour ZIP LEDs (WS2812B). Each LED can display a huge spectrum of colours, enabling vibrant rainbow effects, colou...

SKU: AF-3893 | Brand: Adafruit

The JST PH 3-Pin to Male Header Cable converts a JST PH 3-pin connector into three individual colour-coded wires, each terminated with a 0.1" (2.54 mm) male header pin. It's ideal for extending sensor or LED connectio...

SKU: AF-3966 | Brand: Adafruit

The BMP388 from Bosch is a high-precision barometric pressure and temperature sensor, offering significantly improved altitude accuracy over the BMP280. With altitude noise as low as 0.1 metres and a relative accuracy...

SKU: DF-FIT0007 | Brand: DFRobot

A sturdy metal ball caster made from 1 mm stamped steel plate, capable of supporting loads up to 15 kg. At just 37 g and 20 mm tall, it provides smooth omnidirectional movement without adding significant weight to you...

SKU: AF-3647 | Brand: Adafruit

Precision-machined Swiss-pin male plug headers for a tight, reliable fit. Unlike standard stamped square-pin male headers, these use machined round pins that pair exclusively with Swiss-pin female sockets — they are n...

SKU: AF-3662 | Brand: Adafruit

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need.  Absolutely no soldering required! All t...

SKU: AF-3648 | Brand: Adafruit

The Adafruit PT1000 RTD Temperature Sensor Amplifier is a breakout board for the MAX31865 precision RTD-to-digital converter, configured for PT1000 platinum resistance temperature detectors. It reads 2-, 3-, or 4-wire...

SKU: AF-937 | Brand: Adafruit

This handy USB extension cable will make it easy for you to enclose a device that has a micro-B type port. We think this would be most handy when putting an Arduino Leonardo or Raspberry Pi in a box.The jack half h...

SKU: AF-1131 | Brand: Adafruit

A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs includin...

SKU: AF-1178 | Brand: Adafruit

Rollin' rollin' rollin', you can now roll around smooth as silk with these radial bearings. Often referred to as "skate bearings" They're good for supporting a rotating rod or as a wheel hub. However, these are higher...

SKU: AF-4031 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack so you get left and right channels as well as a ground pin. You can use any 3.5mm stereo cable with this jac...

SKU: AF-1663 | Brand: Adafruit

A matching pair of 3-pin JST SM connector cables — one plug and one receptacle — for creating quick-connect/disconnect points in 3-wire circuits. The locking latch keeps the connection secure while still allowing easy...

SKU: AF-2195 | Brand: Adafruit

A 10-pack of 10µF 50V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic c...

SKU: AF-2193 | Brand: Adafruit

A 10-pack of 100µF 16V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic ...

SKU: AF-2166 | Brand: Adafruit

A low-dropout (LDO) 3.3 V linear voltage regulator based on the ST L4931 in a TO-92 package. With just 0.4 V dropout, it delivers a clean, regulated 3.3 V output from input voltages as low as 3.7 V — well suited for s...

SKU: AF-2324 | Brand: Adafruit

The Adafruit Ultimate GPS HAT adds high-quality GPS and GLONASS positioning to your Raspberry Pi. Built around a PA1616D module, it provides precise location data and a built-in real-time clock (RTC) with coin cell ba...

SKU: AF-2430 | Brand: Adafruit

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also i...

SKU: DF-FIT0085 | Brand: DFRobot

This custom-designed plastic wheel has a rubber tire measuring 1.65" (42 mm) in diameter and is designed to fit the output shafts on our mini metal gearmotors as well as the Solarbotics metal gear motors. Teeth on...

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...