Prototyping & Wiring

SKU: EC-SEL71220A | Brand: Elecrow

A current sensing module based on the Allegro ACS712 Hall effect sensor, capable of accurately measuring both AC and DC current up to ±20 A. The module outputs a proportional analogue voltage that can be read directly...

SKU: AF-4831 | Brand: Adafruit

The Adafruit LTR390 is a dual-purpose UV and ambient light sensor with true UVA sensing at a peak spectral response between 300 and 350 nm. Unlike UV index approximation sensors, the LTR390 has a genuine UV photodiode...

SKU: DF-FIT0720 | Brand: DFRobot

These patch test hooks provide a solderless way to make signal and low-current connections between boards, sensors, and modules. The hook clips grab onto pins, pads, and component legs — perfect for prototyping with c...

SKU: EC-DPO01117E | Brand: Elecrow

The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate ...

SKU: AF-4716 | Brand: Adafruit

The Adafruit MS8607 is a factory-calibrated 3-in-1 sensor that measures barometric pressure, relative humidity, and temperature over I2C. Made by TE Connectivity, this PHT (Pressure, Humidity, Temperature) sensor is a...

SKU: EC-DRA09012K | Brand: Elecrow

An accessory kit for the Raspberry Pi Zero and Zero W that provides adapters and headers to expand the board's compact connectors to full-size interfaces. Includes a clear acrylic case, USB OTG cable, Mini HDMI adapte...

SKU: KI-5625 | Brand: Kitronik

The ZIP Halo is a circular LED board for the BBC micro:bit featuring 24 individually addressable full-colour ZIP LEDs (WS2812B). Each LED can display a huge spectrum of colours, enabling vibrant rainbow effects, colou...

SKU: AF-3893 | Brand: Adafruit

The JST PH 3-Pin to Male Header Cable converts a JST PH 3-pin connector into three individual colour-coded wires, each terminated with a 0.1" (2.54 mm) male header pin. It's ideal for extending sensor or LED connectio...

SKU: AF-3966 | Brand: Adafruit

The BMP388 from Bosch is a high-precision barometric pressure and temperature sensor, offering significantly improved altitude accuracy over the BMP280. With altitude noise as low as 0.1 metres and a relative accuracy...

SKU: AF-3763 | Brand: Adafruit

We're keepin' it wheel with this one! Plastic gear-box motors (also known as 'TT' motors) are an easy and low cost way to get your projects moving. But we've noticed that there are not a lot of nice TT motor&n...

SKU: DF-FIT0007 | Brand: DFRobot

A sturdy metal ball caster made from 1 mm stamped steel plate, capable of supporting loads up to 15 kg. At just 37 g and 20 mm tall, it provides smooth omnidirectional movement without adding significant weight to you...

SKU: AF-3647 | Brand: Adafruit

Precision-machined Swiss-pin male plug headers for a tight, reliable fit. Unlike standard stamped square-pin male headers, these use machined round pins that pair exclusively with Swiss-pin female sockets — they are n...

SKU: AF-3662 | Brand: Adafruit

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need.  Absolutely no soldering required! All t...

SKU: AF-937 | Brand: Adafruit

This handy USB extension cable will make it easy for you to enclose a device that has a micro-B type port. We think this would be most handy when putting an Arduino Leonardo or Raspberry Pi in a box.The jack half h...

SKU: AF-1178 | Brand: Adafruit

Rollin' rollin' rollin', you can now roll around smooth as silk with these radial bearings. Often referred to as "skate bearings" They're good for supporting a rotating rod or as a wheel hub. However, these are higher...

SKU: AF-4031 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack so you get left and right channels as well as a ground pin. You can use any 3.5mm stereo cable with this jac...

SKU: AF-1663 | Brand: Adafruit

A matching pair of 3-pin JST SM connector cables — one plug and one receptacle — for creating quick-connect/disconnect points in 3-wire circuits. The locking latch keeps the connection secure while still allowing easy...

SKU: AF-2195 | Brand: Adafruit

A 10-pack of 10µF 50V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic c...

SKU: AF-2193 | Brand: Adafruit

A 10-pack of 100µF 16V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic ...

SKU: AF-2166 | Brand: Adafruit

A low-dropout (LDO) 3.3 V linear voltage regulator based on the ST L4931 in a TO-92 package. With just 0.4 V dropout, it delivers a clean, regulated 3.3 V output from input voltages as low as 3.7 V — well suited for s...