Light & Colour

SKU: LB-BK-LR0282 | Brand: Little Bird

Description This Light Dependant Resistor (LDR) can be used to easily measure ambient light with your Arduino or other board with analog input. You will need to set this up as a voltage divider with a resistor of a...

SKU: LB-24-LIGHT | Brand: Little Bird

Light-dependent resistors are electronic components whose resistance changes with light intensity. They are also called LDRs, photoresistors, or photoconductors.   It has four pins:3.3V  : While 'VCC'...

SKU: LB-LR0282 | Brand: Little Bird

This Light Dependant Resistor (LDR) can be used to easily measure ambient light with your Arduino or other board with analog input. You will need to set this up as a voltage divider with a resistor of around 10KΩ. ...

SKU: LB-LS2299 | Brand: Little Bird

A UV detection sensor module that measures ultraviolet light intensity in the 200–370 nm wavelength range. The analogue output (0–1 V DC) is proportional to the UV Index, making it suitable for measuring UV exposure i...

SKU: AF-2831 | Brand: Adafruit

This Photo Transistor Light Sensor is a simple sensor that detects ambient light. It's kind of the opposite of an LED - when light hits the little chip inside, it induces current to flow from the long pin...

SKU: SF-SEN-09088 | Brand: SparkFun

This is a very small light sensor. A photocell changes (also called a photodetector, photo resistor, CdS or photoconductive cell) resistance depending on the amount of light it is exposed to. These little sensors make...

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: EF-EF04093 | Brand: ElecFreaks

Octopus Analog UV sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the...

SKU: DF-SEN0043 | Brand: DFRobot

An analog ambient light sensor based on the TEMT6000 detector, which has a spectral response closely matching the human eye with very low IR sensitivity. It outputs an analog voltage proportional to the ambient light ...

SKU: EF-EF04092 | Brand: ElecFreaks

The Octopus Light Sensor Brick reads the ambient light level of its surrounding environment and outputs an analog signal. The 3-pin GVS connector makes it easy to plug into micro:bit expansion boards, Arduino, and oth...

SKU: LB-LS0239 | Brand: Little Bird

This e-textiles ambient light sensor uses the TEMT6000 phototransistor to detect light levels. Designed for wearable electronics, it features a compact 20 mm round PCB that's only 0.8 mm thick — thin enough to sew int...

SKU: SF-BOB-08688 | Brand: SparkFun

Basic breakout board for the TEMT6000 Ambient Light Sensor. Only what you need, nothing you don’t. Sensor acts like a transistor - the greater the incoming light, the higher the analog voltage on the signal pin. Docu...

SKU: AF-2748 | Brand: Adafruit

The Adafruit ALS-PT19 is a compact analog light sensor that provides a simple voltage output proportional to ambient light intensity. Its spectral response closely matches that of the human eye, thanks to a high infra...

SKU: TB-XC4574 | Brand: Little Bird

The light sensor, also known as the light dependent resistor (LDR). Typically, the resistance of the light sensor will decrease when the ambient light intensity increases.   Linksprite Page   Specificat...

SKU: SF-COM-08348 | Brand: SparkFun

The TEMT6000x01 is a compact ambient light sensor that operates as an NPN phototransistor. The more light that hits the sensor, the stronger the base bias, producing an analog output proportional to the ambient light ...