Environmental (temperature, humidity, air quality)

SKU: DF-SEN0572 | Brand: DFRobot

The Fermion MEMS H2 Sensor is a compact hydrogen gas detection module using micro-electromechanical system (MEMS) technology. It provides qualitative measurement of hydrogen concentration from 0.1 to 1000 ppm via an a...

SKU: DF-SEN0566 | Brand: DFRobot

Fermion: MEMS Volatile Organic Compounds VOC Gas Sensor employs state-of-the-art microelectromechanical system (MEMS) technology, endowing the sensor with compact dimensions (13x13x2.5mm), low power consumption (<20mA...

SKU: LB-LR0205 | Brand: Little Bird

An alcohol sensor module for Arduino with both digital (TTL) and analog output. It detects alcohol vapour in the 10–1000 PPM range, with analog output voltage increasing proportionally with concentration. The module a...

SKU: DF-SEN0134 | Brand: DFRobot

The Gravity MQ-9 gas sensor detects carbon monoxide (CO) and combustible gases including methane and propane. It uses a semiconductor SnO2 sensing element that cycles between high and low temperatures — detecting CO a...

SKU: DF-SEN0496 | Brand: DFRobot

This full-scale oxygen sensor uses an original AO2 CiTiceL electrochemical probe to measure oxygen concentrations from 0–100%Vol via I2C digital output. A built-in calibration algorithm on the signal board supports si...

SKU: DF-SEN0322 | Brand: DFRobot

The Gravity: I2C Oxygen Sensor is based on electrochemical principles and it can measure the ambient O2 concentration accurately and conveniently. With high anti-interference ability, high stablility and high sensitiv...

SKU: PL-1634 | Brand: Pololu

The MQ-3 is a semiconductor gas sensor that detects alcohol vapour at concentrations from 0.04 mg/L to 4 mg/L — a range suitable for building a breathalyser. It provides a simple analog voltage output that requires on...

SKU: DF-SEN0132 | Brand: DFRobot

INTRODUCTION This is an Arduino Carbon Monoxide Sensor. It uses MQ7 probe to detect Carbon Monoxide (CO) concentrations in the air from 20 to 2000ppm. The sensitivity ca...

SKU: SF-SEN-08880 | Brand: SparkFun

The MQ-3 is an alcohol gas sensor suitable for detecting alcohol concentration in the air, similar to a breathalyser. It provides an analog resistive output based on alcohol concentration, with high sensitivity and fa...

SKU: AF-5593 | Brand: Adafruit

The AGS02MA is a compact MOX-based TVOC (Total Volatile Organic Compounds) gas sensor with an I2C interface. It features a built-in ADC that outputs gas resistance and parts-per-billion (ppb) readings — higher ppb val...

SKU: DF-SEN0476 | Brand: DFRobot

This is a sensor that detects phosphine concentration and supports three output modes: analog, I2C, and UART. The probe has been calibrated at the factory, which can quickly and accurately measure the concentration of...

SKU: DF-SEN0128 | Brand: DFRobot

An analogue alcohol gas sensor based on the MQ-3 probe, designed for use with Arduino and other microcontrollers. The sensor outputs a voltage proportional to the concentration of alcohol vapour in the surrounding air...

SKU: EC-SES90101S | Brand: Elecrow

The MQ-9 is an analog gas sensor module with high sensitivity to carbon monoxide (CO), methane, propane, and LPG. It uses an SnO2 sensing element that changes conductivity in the presence of target gases, making it su...

SKU: SS-101020044 | Brand: Seeed Studio

Alcohol sensor is semiconductor sensor for alcohol detection. It has good sensitivity and fast response to alcohol, suitable for portable alcohol detector. Specifications Power requirements: 5 VDC @ ~120 ...