Circuitry & IOT

SKU: AF-1699 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm...

SKU: AF-2384 | Brand: Adafruit

The "poor man's" accelerometer/motion sensor! These spring-vibration switches are medium sensitivity non-directional vibration induced trigger switches. Inside is a medium hardness spring coiled around a long metal...

SKU: SF-PRT-12083 | Brand: SparkFun

This 4xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF swi...

SKU: SF-PRT-11892 | Brand: SparkFun

Now for all of your coin cell battery surface mount needs, the 20mm SMD Coin Cell Holder. This holder fits our 20mm Lithium Ion coin cell battery and holds the battery in place with friction. The metal housing connect...

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-PRT-10897 | Brand: SparkFun

These are 155mm long jumpers terminated as male to male. Use these to jumper from any female header on any board, to any other female header. Multiple jumpers can be installed next to one another on a 0.1" header. Com...

SKU: SF-TOL-12966 | Brand: SparkFun

The digital multimeter (DMM) is an essential tool in every electronic enthusiasts arsenal. The SparkFun Digital Multimeter, however, is not your average multimeter, it features a loud continuity sound, current/voltage...

SKU: LB-LR0178-350 | Brand: Little Bird

SKU: DF-DFR1075 | Brand: DFRobot

The FireBeetle 2 ESP32-C6 is a low-power IoT development board built around a 160MHz RISC-V single-core processor. It supports Wi-Fi 6 (802.11ax), Bluetooth 5, Zigbee 3.0, Thread 1.3, and the Matter smart home standar...

SKU: SF-WRL-24408 | Brand: SparkFun

The SparkFun ESP32-S3 Thing Plus adds a powerful and versatile IoT development platform to the Thing Plus product line. It features the ESP32 WROOM-S3 MINI wireless module from espressif™. The ESP32 WROOM-S3 is built ...

SKU: EF-EF02054 | Brand: ElecFreaks

DescriptionWukong 2040 is a multifunctional Breakout Board designed for Raspberry Pi Pico. In terms of functions, it is equipped with a buzzer, A\B buttons, rainbow lights, motor interface, reset button, etc., to meet...

SKU: AF-5715 | Brand: Adafruit

The ESP32-H2-DevKitM-1 is an entry-level development board based on the ESP32-H2-MINI-1 module, featuring Bluetooth Low Energy 5, IEEE 802.15.4, Thread, Matter, and Zigbee support on a single chip. It's an ultra-low-p...

SKU: DF-DFR0896 | Brand: DFRobot

The ESP32-S3-WROOM-1-N4 is a powerful Wi-Fi and Bluetooth LE MCU module built around the ESP32-S3 SoC. Featuring a dual-core Xtensa LX7 processor running at up to 240MHz, 4MB SPI flash, and hardware acceleration for n...

SKU: AF-5348 | Brand: Adafruit

The Adafruit QT Py ESP32-S2 with uFL Antenna Port is the extended-range version of the QT Py ESP32-S2. Instead of an on-board antenna, it features a uFL connector so you can attach any 2.4 GHz Wi-Fi antenna for signif...

SKU: EC-SPM32100S | Brand: Elecrow

This Moisture Sensor can be used to detect the moisture of soil or your pet plant's water level, let the plants in your garden reach out for human help. With the Octopus Electronic Bricks interface can very easy to us...

SKU: EC-SEA0001T | Brand: Elecrow

The Crowtail Starter Kit for Arduino is a beginner-friendly electronics kit built around the Crowduino Uno-SD board and the Crowtail modular connector system. With 22 plug-and-play modules and over 20 guided tutorials...

SKU: EC-ACS70028DH | Brand: Elecrow

The Dual Channel H-Bridge Motor Shield is composed of 2 discrete MOSFET H-bridge, designed to drive two DC motor with max current 8A. It is made up of 8 N-channel MOSFET IRF3205S and 4 pcs of half bridge motor control...

SKU: EF-EF04093 | Brand: ElecFreaks

Octopus Analog UV sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the...