Circuitry Accessories

SKU: SF-TOL-18342 | Brand: SparkFun

The digital multimeter (DMM) is an essential tool in every electronic enthusiasts arsenal. This Smart Digital Multimeter, however, is not your average multimeter, it features a continuity sound at less than about 40±1...

SKU: SF-CAB-15186 | Brand: SparkFun

A 10-pack of cables with an alligator clip on one end and a female header on the other. These cables bridge the gap between clip-based prototyping and standard 0.1" pin headers, making it easy to connect alligator cli...

SKU: AF-3718 | Brand: Adafruit

Are you still looking for that perfect PCB holder? The hefty yet portable Heavy Stainless Steel PCB Holder will rock out when you rework out. These were initially marketed for people doing cell phone repair an...

SKU: AF-1606 | Brand: Adafruit

The Adafruit Perma-Proto Full-Sized Breadboard PCB mirrors the layout of a standard full-size solderless breadboard, making it simple to transfer prototyped circuits to a permanent soldered board. With 60 rows of 5-ho...

SKU: DF-FIT0030 | Brand: DFRobot

These 23 cm (9″) female-to-female jumper wires are a prototyping essential. Use them to connect between male headers on Arduino boards, IO shields, sensors, and breadboards. Multiple wires sit neatly side by side on s...

SKU: SF-PRT-08671 | Brand: SparkFun

This is a simple two wire cable. Great for jumping from board to board. 2-pin JST connector on one end, bare cable on the opposite end. Dimensions: 100mm length Documents: JST connector

SKU: SF-PRT-13032 | Brand: SparkFun

A simple breadboard power supply that takes a 6–12 V input and outputs a regulated 5 V or 3.3 V. All headers are at 0.1" pitch for direct insertion into a standard breadboard, with the output pins spaced to power both...

SKU: AF-735 | Brand: Adafruit

An 8-bit logic level shifter in a breadboard-friendly DIP package. The 74LVC245 converts between 3.3V and 5V logic levels, making it easy to interface modern 3.3V sensors and peripherals with 5V microcontrollers like ...

SKU: AF-760 | Brand: Adafruit

A 40-piece set of premium male-to-male jumper wires in a rainbow ribbon cable format. Each wire is 12″ (300mm) long with 0.1″ (2.54mm) male header contacts on both ends, fitting cleanly on standard-pitch headers and b...

SKU: AF-793 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" female ...

SKU: AF-1955 | Brand: Adafruit

These Male/Male Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbo...

SKU: AF-2017 | Brand: Adafruit

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 2x4 point solder-less breadboard is a good way to add some solderless prototyping space if you just need to have...

SKU: SF-PRT-09385 | Brand: SparkFun

A pack of 10 premium 12″ (30 cm) male-to-female jumper wires for breadboarding, prototyping, and connecting to 0.1″ pitch headers. Each wire has a male pin on one end and a female socket on the other, making them vers...

SKU: LB-LS7240-F | Brand: Little Bird

Introducing the perfect solution for prototyping - our Full-size Permanent Solder Breadboard PCB! With this board, you can easily transfer your circuit from a solderless breadboard to a more permanent solution wi...

SKU: SF-PRT-18769 | Brand: SparkFun

This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover as well as an ON/OFF switch that can be used to control power to your project. The ...

SKU: AF-1518 | Brand: Adafruit

The Adafruit Flex Perma-Proto is a half-sized breadboard-layout prototyping board made from ultra-thin polyamide film. It bends, twists, and can even be cut to shape with scissors — perfect for wearables, curved enclo...

SKU: DF-FIT0141 | Brand: DFRobot

A 6×AA battery holder with a DC 2.1mm power jack that plugs directly into an Arduino's barrel jack input. Creates a 7.2V rechargeable battery pack from NiMH/NiCd cells or a 9V pack from alkaline cells. Features mounti...

SKU: SF-PRT-14299 | Brand: SparkFun

This is a unique two-cell AA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been terminated with a JST-PH connector. The connector mates the JST socket on the micro:bit perfectly...

SKU: SF-PRT-14219 | Brand: SparkFun

A 2×AAA battery holder with a sliding cover and built-in ON/OFF switch. The cover keeps batteries secure, and the switch provides convenient power control for your project. Wire leads are approximately 150 mm long wit...

SKU: SF-PRT-09835 | Brand: SparkFun

This is a simple 4 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector. The connector mates with the barrel jack on the Arduino (among a numbe...