Breakouts

SKU: AF-1381 | Brand: Adafruit

This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can al...

SKU: DF-TEL0122 | Brand: DFRobot

DFRobot FireBeetle series are low power consumption controllers designed for Internet of Things (IoT) development. The FireBeetle series are aiming straight at the point fast and convenient low-power IoT bu...

SKU: AF-1764 | Brand: Adafruit

Simple but effective - this breakout board has a USB Mini-B connector, with all 5 pins broken out. Great for pairing with a microcontroller with USB support, or adding USB 5V power to a project.Comes with one fully...

SKU: AF-1762 | Brand: Adafruit

These breakout PCBs make it easy to use 5050-size SMD LEDs on a solderless breadboard. Solder a 5050 LED to either side of the PCB and the pins drop straight into standard 0.1″ breadboard rows — no adapter wiring need...

SKU: AF-1782 | Brand: Adafruit

This I2C digital temperature sensor is one of the more accurate/precise we've ever seen, with a typical accuracy of ±0.25°C over the sensor's -40°C to +125°C range and precision of +0.0625°C. They work great with any ...

SKU: AF-1868 | Brand: Adafruit

A simple breakout board with a CR1220 coin cell battery holder pre-soldered and broken out to 0.1″ pitch pins. Ideal for powering very low-current projects or providing battery backup for a real-time clock (RTC) modul...

SKU: AF-1870 | Brand: Adafruit

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit ...

SKU: AF-2104 | Brand: Adafruit

This 2x8 (16 pin - 0.1" spaced) IDC Breadboard Helper is great in conjunction with any 16-pin IDC cables. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles...

SKU: AF-2270 | Brand: Adafruit

The "poor woman's" Raspberry Pi A+ / B+ / Pi 2 cobbler! This combo of 2x20 pin (0.1 spaced) header and socket is for our popular GPIO Ribbon Cable for Raspberry Pi Model A+/B+/Pi 2 (40 pins).  It comes in...

SKU: AF-2107 | Brand: Adafruit

The Adafruit USB Isolator provides galvanic isolation between your computer's USB port and connected devices, protecting against harmful noise, ground loops, surges, and voltage spikes. Based on Analog Devices' USB is...

SKU: AF-2478 | Brand: Adafruit

Add a full-colour touchscreen to your project with this 2.4" TFT LCD breakout. The 240×320 pixel display delivers vivid RGB colour with individual pixel control, driven by the ILI9341 controller with built-in RAM buff...

SKU: DF-FIT0099 | Brand: DFRobot

A prototyping board is one of the main steps in hardware development, also called a perf board. Breadboard, wiring and punching in chips, resistors and leds is probably the first step. While this is good to confirm a...

SKU: DF-SEN0097 | Brand: DFRobot

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier ...

SKU: SF-PRT-14322 | Brand: SparkFun

These stackable headers are made to work with the Particle Photon and Photon ProtoShield boards. Each header adds a great deal of connectivity to your next Photon project. Each order includes one 1x12 stackable header...

SKU: DF-DFR0164 | Brand: DFRobot

This is a new version of the FTDI breakout board features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The 8U2 firmware uses the standard USB COM drivers, and no ...

SKU: DF-DFR0175 | Brand: DFRobot

This is a new IIC LCD backpack which supports Gadgeteer interface (IDC10). It allows gadgeteer user to play with LCD160X. The IIC LCD Backpack is a small PCB that can be soldered to the back of an LCD so tha...

SKU: AF-2711 | Brand: Adafruit

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi  with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderl...

SKU: AF-2743 | Brand: Adafruit

This adapter board is designed to make it easier to use ARM dev boards that use slimmer 2x5 (0.05"/1.27mm pitch) SWD cables for programming.  It's helpful for using products like the JTAGulator, STLink or SEGG...

SKU: DF-FIT0203 | Brand: DFRobot

This is a very basic double sided prototyping board with standard 0.1" spacing through holes and four 3mm diameter mounting holes. There are 22x26 holes in total. Great for quickly prototyping stackable circuit...

SKU: SF-BOB-09110 | Brand: SparkFun

This is the breakout board for the thumb joystick. Pins are broken out to a 0.1" header and includes 4 mounting holes in the corners.