Breakouts

SKU: AF-6001 | Brand: Adafruit

The Adafruit Reversible USB Type A Plug Connector Breakout breaks out a reversible USB Type A plug to breadboard-friendly pins. The connector uses a thin centre contact so it can be plugged in either way — no more gue...

SKU: AF-5991 | Brand: Adafruit

The Adafruit USB Type C Power Delivery Dummy (I2C or Switchable) lets you tap into USB-C Power Delivery to get 5V, 9V, 12V, 15V, 18V, or 20V from any compatible USB-C charger or wall adapter — no soldering required. B...

SKU: AF-5882 | Brand: Adafruit

The Adafruit DC Power BFF Add-On lets you power your QT Py or Xiao development board from a DC source up to 20V. The on-board MPM3610 integrated buck converter steps down the input to 5V at up to 1A, with no heat sink...

SKU: DF-DFR0912 | Brand: DFRobot

The 2-Channel Level Converter translates 12V signals down to 5V using optocoupler isolation, making it easy to interface industrial sensors and PLC signals with 5V microcontrollers like Arduino. It supports common ano...

SKU: DF-SEN0441 | Brand: DFRobot

This is a hydrogen and nitrogen oxide gas concentration sensor launched by DFRobot. The sensor uses MEMS technology to support gas concentration detection of NO, NO2 and H2. The matching sample code integrates the co...

SKU: SF-SEN-17052 | Brand: SparkFun

The MQ-136 is a Hydrogen Sulfide detection sensor with a sensing range of 1 - 200ppm. The sensing element is SnO2, which has lower conductivity in clean air. When H₂S gas exists, the sensor’s conductivity gets higher ...

SKU: SF-SEN-17053 | Brand: SparkFun

The MQ-137 is an ammonia (NH3) gas sensor from Winsen, designed to detect ammonia concentrations in the air. The sensing element is tin dioxide (SnO2), which has lower conductivity in clean air and increases in conduc...

SKU: AF-3877 | Brand: Adafruit

A hex Schmitt-trigger inverter IC that doubles as a handy logic level shifter. The 74AHCT14 provides six independent inverter channels, each with Schmitt-trigger inputs for clean switching on noisy or slow-transitioni...

SKU: EF-EF11083 | Brand: ElecFreaks

The Octopus Dust Sensor Module features the Sharp GP2Y1010AU0F optical dust sensor, capable of detecting fine particles with a diameter as small as 0.8 μm. It uses an infrared LED and phototransistor to measure dust d...

SKU: LB-00061 | Brand: Little Bird

OverviewDeveloped as a quick starter board for the less experienced we envision this board as the follow up to your first soldering session.In isolation this board will produce a middle C note by hovering over the boa...

SKU: AF-1031 | Brand: Adafruit

This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how close the nearest object is. Comes with 8" long 3-JST interface wire...

SKU: AF-4132 | Brand: Adafruit

The Adafruit GPIO Expander Bonnet adds 16 extra digital I/O pins to your Raspberry Pi over I²C. Based on the MCP23017 chip, it plugs directly onto the Pi's 40-pin header and communicates via SDA/SCL, leaving your othe...

SKU: AF-2039 | Brand: Adafruit

A 16×8 LED matrix backpack kit featuring two ultra-bright 1.2" blue 8×8 round LED matrices on a single I2C-controlled driver board. The HT16K33 chip handles all the multiplexing, so you only need two I2C pins (SDA and...

SKU: SF-BOB-09322 | Brand: SparkFun

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>...

SKU: SF-SEN-11862 | Brand: SparkFun

RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-3LA, a very simple...

SKU: SF-SEN-11769 | Brand: SparkFun

The Line Follower sensor is an add-on for your RedBot that gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. By measurin...

SKU: AF-164 | Brand: Adafruit

The Sharp GP2Y0A21YK0F is an infrared distance sensor that measures distances from 10 cm to 80 cm by bouncing IR light off objects. It outputs an analogue voltage proportional to distance — approximately 3 V at 10 cm ...

SKU: AF-3182 | Brand: Adafruit

The Pimoroni Mini Black HAT Hack3r breaks out all 40 GPIO pins from your Raspberry Pi while still allowing a HAT or pHAT to sit on top. Connect via the included ribbon cable and access every pin — labelled with functi...

SKU: SF-WIG-13279 | Brand: SparkFun

The SparkFun Large Digit Driver is a chainable controller board that solders directly to the back of 6.5" 7-segment LED displays. It uses the TPIC6C596 shift register IC to drive individual segments, making it easy to...

SKU: AF-3199 | Brand: Adafruit

The Adafruit MiCS-5524 Gas Sensor Breakout is a robust MEMS sensor from SGX Sensortech for detecting carbon monoxide, natural gas leaks, alcohol, and volatile organic compounds (VOCs). It provides a simple analogue vo...