Breakouts

SKU: DF-DFR0250 | Brand: DFRobot

A boost converter module that takes two AA batteries and outputs a stable 5 V supply for your circuits. Built around the TI TPS61032 boost chip, it accepts input voltages from 1.8–4.5 V and delivers up to 5 V @ 1 A — ...

SKU: SF-SEN-00242 | Brand: SparkFun

The Sharp GP2Y0A21YK is an infrared proximity sensor with an analogue voltage output that varies with distance — from 3.1 V at 10 cm to 0.4 V at 80 cm. It uses an IR emitter and position-sensitive detector to measure ...

SKU: AF-255 | Brand: Adafruit

THIS IS THE LATEST VERSION 2.1The ChronoDot RTC is an extremely accurate real time clock module, based on the DS3231 temperature compensated RTC (TCXO). It includes a CR1632 battery, which should last at least 8 years...

SKU: SF-SEN-13030 | Brand: SparkFun

The SparkFun RFID Reader Breakout converts the 2mm pin spacing of ID-series RFID readers to breadboard-friendly 0.1" headers. Compatible with the ID-3LA, ID-12LA, and ID-20LA readers, this board lets you solder the re...

SKU: AF-1903 | Brand: Adafruit

The PowerBoost 500 Basic is a compact DC/DC boost converter that takes input from 1.8V or higher and outputs a steady 5.2V — perfect for powering portable 5V projects from batteries. The slightly elevated 5.2V output ...

SKU: DF-DFR0411 | Brand: DFRobot

INTRODUCTION This DC motor has an integrated transistor built in to the board, eliminating the need for a motor driver. Use PWM to control it for all your DIY project needs. It uses the 3 pi...

SKU: DF-TEL0010 | Brand: DFRobot

This USB to TTL converter combine the USB-232-1 (USB to Single RS232 Adapter) and TTL-232-1 (Port-powered RS232/TTL converter) allows you to convert USB to TTL/CMOS compatible levels and vice versa. It can be use...

SKU: DF-SEN0220 | Brand: DFRobot

The Gravity UART Infrared CO2 Sensor uses non-dispersive infrared (NDIR) technology to measure carbon dioxide concentrations from 0 to 50,000 ppm. It offers excellent selectivity with no oxygen dependency, built-in te...

SKU: SF-COM-09542 | Brand: SparkFun

The QRE1113 is a small IR reflectance sensor. This sensor is often used in line following robots because, if it can sense if a surface is white or black. There are four pins on the QRE1113 - two control the IR em...

SKU: SF-ROB-09454 | Brand: SparkFun

The SparkFun QRE1113 Line Sensor Breakout (Digital) is a compact IR reflectance sensor board that outputs a digital signal based on surface reflectivity. It uses a capacitor discharge circuit — the faster the 10 nF ca...

SKU: DF-DFR1193 | Brand: DFRobot

The Gravity LTC4316 I2C Address Shifter resolves I2C address conflicts, allowing multiple sensors with the same address to operate on a single bus. Insert this module between your microcontroller and sensor – address ...

SKU: AF-6420 | Brand: Adafruit

The Adafruit SPA06-003 is an affordable barometric pressure and temperature sensor from Goertek, ideal for basic environmental sensing and DIY quadcopter builds. It measures 300–1100 hPa (approximately −500 to +9000 m...

SKU: SF-WRL-28896 | Brand: SparkFun

  The RockBLOCK 9704 by Ground Control is a breakout board for the new Iridium 9704 including a built-in patch antenna and a supercap charger to enable low power operation. If you need low data rate connectiv...

SKU: AF-6353 | Brand: Adafruit

The Adafruit STSPIN220 Stepper Motor Driver Breakout makes controlling bipolar stepper motors simple with a GPIO-only interface — just two pins (DIR and STEP) are all you need. It defaults to 1/16 microstepping and su...

SKU: DF-SEN0598 | Brand: DFRobot

An IP68-rated ultrasonic obstacle avoidance sensor specifically designed for underwater applications. With a measurement range of 2–300cm and UART output, this compact sensor enables underwater vehicles and robots to ...

SKU: AF-6001 | Brand: Adafruit

The Adafruit Reversible USB Type A Plug Connector Breakout breaks out a reversible USB Type A plug to breadboard-friendly pins. The connector uses a thin centre contact so it can be plugged in either way — no more gue...

SKU: AF-5991 | Brand: Adafruit

The Adafruit USB Type C Power Delivery Dummy (I2C or Switchable) lets you tap into USB-C Power Delivery to get 5V, 9V, 12V, 15V, 18V, or 20V from any compatible USB-C charger or wall adapter — no soldering required. B...

SKU: AF-5882 | Brand: Adafruit

The Adafruit DC Power BFF Add-On lets you power your QT Py or Xiao development board from a DC source up to 20V. The on-board MPM3610 integrated buck converter steps down the input to 5V at up to 1A, with no heat sink...

SKU: DF-DFR0912 | Brand: DFRobot

The 2-Channel Level Converter translates 12V signals down to 5V using optocoupler isolation, making it easy to interface industrial sensors and PLC signals with 5V microcontrollers like Arduino. It supports common ano...

SKU: DF-SEN0441 | Brand: DFRobot

This is a hydrogen and nitrogen oxide gas concentration sensor launched by DFRobot. The sensor uses MEMS technology to support gas concentration detection of NO, NO2 and H2. The matching sample code integrates the co...