Breakouts

SKU: SF-PRT-11214 | Brand: SparkFun

MOSFETs are awesome. They’re like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. The board also ha...

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: DF-DFR0411 | Brand: DFRobot

INTRODUCTION This DC motor has an integrated transistor built in to the board, eliminating the need for a motor driver. Use PWM to control it for all your DIY project needs. It uses the 3 pi...

SKU: SF-ROB-09454 | Brand: SparkFun

The SparkFun QRE1113 Line Sensor Breakout (Digital) is a compact IR reflectance sensor board that outputs a digital signal based on surface reflectivity. It uses a capacitor discharge circuit — the faster the 10 nF ca...

SKU: SF-BOB-28467 | Brand: SparkFun

A simple breakout board that converts the 22-pin HSTX/camera/display connector to standard 0.1" through-hole pins. Perfect for prototyping and debugging when you need direct access to all the signals from your RP2350 ...

SKU: DF-DFR1037 | Brand: DFRobot

##Introduction This is a 2-channel analog voltage output DAC module with PWM communication, 8-bit resolution, and 0.5% precision. It is well-suited for control projects operating within the 3.3V range, such as ESP32, ...

SKU: AF-5948 | Brand: Adafruit

The Adafruit PiCowbell OV5640 Camera Breakout adds a 5-megapixel camera with a 120-degree low-distortion wide-angle lens to your Raspberry Pi Pico or Pico W. Capture raw RGB images for analysis or use the OV5640's bui...

SKU: AF-5905 | Brand: Adafruit

The Adafruit Proto Under Plate PiCowbell is a single-slot prototyping base for the Raspberry Pi Pico or Pico W. It provides a reset button, a STEMMA QT / Qwiic connector, a prototyping grid, and double-row socket head...

SKU: SF-COM-21337 | Brand: SparkFun

The SparkFun 3.3V Buck Regulator Breakout features the AP3429A from Diodes Inc., a 2A step-down DC-DC converter with an input voltage range of 2.7V to 5.5V. This full-size, 1in. x 1in. version of our buck regulator bo...

SKU: AF-5545 | Brand: Adafruit

The Adafruit PCF8574 GPIO Expander Breakout is an affordable 8-channel I2C GPIO expander that adds extra digital I/O to any microcontroller project. Simply connect over I2C and control up to 8 additional pins for butt...

SKU: DF-DFR0844 | Brand: DFRobot

After purchasing an open-source product that is not electrical level compatible, you may find that your sensor cannot work normally or even is easy to be damaged because the level of the sensor and your controller are...

SKU: DF-DFR0843 | Brand: DFRobot

After purchasing an open-source product that is not electrical level compatible, you may find that your sensor cannot work normally or even is easy to be damaged because the level of the sensor and your controller are...

SKU: DF-DFR0835 | Brand: DFRobot

This 4.7" e-ink display board integrates an ESP32-WROVER-E module (ESP32-D0WDQ6 V3) with 16MB Flash and 8MB PSRAM, providing a complete development platform for low-power e-ink projects. The display supports 16 graysc...

SKU: SF-SEN-17372 | Brand: SparkFun

Passive Infrared (PIR) sensors are great for detecting motion in a small area around the sensor. The 170µA SparkFun EKMC4607112K PIR Breakout is a simple board equipped with an EKM-series PIR sensor from Panasonic®. T...

SKU: SF-PRT-17253 | Brand: SparkFun

The micro:bit Edge Connector allows you to expand the capabilities of the micro:bit development platform. This version of the connector features 40, right angle, SMD pins. Add this part to your board to create a handy...

SKU: SF-ROB-16836 | Brand: SparkFun

The SparkFun ProDriver makes it easy to start developing with the TC78H670FTG bipolar stepper motor driver from Toshiba! Latch terminals provide instant solder-less connections to every feature offered. Use our extens...

SKU: EF-EF04075 | Brand: ElecFreaks

OCTOPUS Magnetic Switch is a kind of electric brick carrying magnetic switch and compatible with OCTOPUS series. It mainly consists of WBSF12 dry reed switch. WBSF12 is a dry reed tube with frequently open contact ...

SKU: EF-EF04096 | Brand: ElecFreaks

Octopus 3V laser sensor is the laser emission electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the s...

SKU: AF-1362 | Brand: Adafruit

This breakout board is the simplest way to create a project with mutiple capacitive touch sensors. No microcontroller is required here - just power with 1.8 to 5.5VDC and connect up to 5 conductive pads to the 5 left-...

SKU: AF-1719 | Brand: Adafruit

Make a small linear display with multiple colors using this elegant bi-color LED bargraph. Only 1.2" long, it is quite visible but not so large it wont plug into a breadboard! 24 LEDs are contained in the plastic b...