Brands

SKU: DF-DFR0556 | Brand: DFRobot

A 16×2 character LCD display module from DFRobot's Gravity series, connecting to your Arduino or microcontroller via a simple I²C interface — just two data wires instead of the many parallel connections a standard LCD...

SKU: AF-2783 | Brand: Adafruit

ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 4.7K Ω Resistors. More specifically, they are carbon film,...

SKU: PR-PIM300 | Brand: Little Bird

The Pico HAT Hacker is an ultra-thin breakout board that gives you full access to all 40 GPIO pins on your Raspberry Pi. At just 0.8 mm thick, it solders directly onto the Pi's header pins while leaving enough pin hei...

SKU: AF-1438 | Brand: Adafruit

The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. D...

SKU: LB-LR0401 | Brand: Little Bird

Product Overview The L3G4200D Gyroscope Module is a low power 3-Axis angular rate sensor with temperature data. The gyroscope shows the rate of change in rotation on its X,Y and Z axes. Temperature output data and...

SKU: LB-ETEXTILEADXL335 | Brand: Little Bird

  This is a three axis accelerometer designed for E-Textiles. Based on the ADXL335 MEMS accelerometer from Analog Devices, this Accelerometer can detect joint movement as well as inclination and vibration. The ...

SKU: AF-3211 | Brand: Adafruit

The Adafruit RGB Matrix Bonnet makes it easy to drive HUB75-type RGB LED matrices directly from your Raspberry Pi. Simply plug the bonnet onto any Pi with a 40-pin GPIO header, connect your matrix via the IDC cable, a...

SKU: LB-LS0153R | Brand: Little Bird

Red Wire Wrap Wire on Spool 250m 30AWG Wire Wrapping Wire, 30 AWG External Material :PVC PVC insulation, Tinned copper conductor Diameter: 0.5 mm Inner diameter:0.25 mm Length:250 meters Heat-resistant: 80 degrees

SKU: LB-LS0305 | Brand: Little Bird

Soldering Solder Iron Tip Cleaner Steel Cleaning Wire Sponge BallIn order to reduce the temperature decreasing of soldering tip, you should not clean it with water.After you using the Sponge, it should be cleaned out ...

SKU: DF-SEN0257 | Brand: DFRobot

The Gravity Analog Water Pressure Sensor measures water or gas pressure and outputs a linear 0.5–4.5 V analogue signal proportional to the applied pressure (0–1.6 MPa). Using the DFRobot Gravity 3-pin interface, it co...

SKU: AF-3708 | Brand: Adafruit

If you didn't think that the Raspberry Pi Zero W could possibly get any better, then boy do we have a pleasant surprise for you! The new Raspberry Pi Zero WH offers all the benefits of the Pi Zero W, b...

SKU: AF-1597 | Brand: Adafruit

This professional-grade solder sucker features a machined aluminium body and a replaceable silicone rubber tip that won't melt on contact with hot solder joints. The smooth spring-loaded action provides reliable, powe...

SKU: SF-DEV-14495 | Brand: SparkFun

The SparkFun Qwiic Adapter provides the perfect means to make any old I2C board into a Qwiic-enabled board. This adapter breaks out the I2C pins from the Qwiic connectors to pins that you can easily solder with you...

SKU: AF-1769 | Brand: Adafruit

This JST PH 2-pin SMT right-angle connector is a surface-mount header designed to accept standard JST PH 2-pin plugs. It's commonly used as a battery connector on microcontroller boards, LiPo chargers, and small elect...

SKU: AF-1683 | Brand: Adafruit

This latching pushbutton toggle switch provides a simple push on / push off action — press once to turn on, press again to turn off. It delivers a satisfying tactile click and can reliably handle up to 500 mA at up to...

SKU: AF-2217 | Brand: Adafruit

The Adafruit Audio FX Sound Board with 2×2W Amp is a standalone audio trigger with a built-in stereo Class D amplifier — no Arduino or programming required. Simply drag and drop WAV or OGG sound files over USB, wire u...

SKU: AF-1222 | Brand: Adafruit

The Adafruit GEMMA V2 is a tiny, coin-sized wearable microcontroller board powered by an ATtiny85 processor. At just 28 mm in diameter, it's small enough to fit into any sewable or wearable project, and affordable eno...

SKU: DF-DFR0052 | Brand: DFRobot

The DFRobot Vibration Sensor buffers a piezoelectric transducer that responds to strain changes by generating a measurable output voltage change which is propotional with the strength of vibration.So you can know the...

SKU: DF-SEN0101 | Brand: DFRobot

An RGB colour sensor breakout board based on the TAOS TCS3200 chip, with four built-in white LEDs for illumination. The TCS3200 can detect and measure a wide range of visible colours by converting light intensity to a...

SKU: DF-SEN0114 | Brand: DFRobot

A resistive soil moisture sensor that reads the water content of surrounding soil by measuring electrical resistance between its two probes. Wetter soil conducts more easily (lower resistance), while dry soil conducts...