Brands and Manufacturers

SKU: SF-CAB-10649 | Brand: SparkFun

A 3-foot (approximately 90 cm) length of 10-wire ribbon cable. Useful for making clean, organised multi-conductor connections in electronics projects — ideal for connecting to IDC crimp-on connectors. Specifications ...

SKU: AF-3317 | Brand: Adafruit

The Adafruit VL53L0X is a Time-of-Flight (ToF) distance sensor from ST that uses an invisible laser to measure distances from approximately 50 mm to 1200 mm. By timing how long the laser light takes to bounce back, it...

SKU: AF-589 | Brand: Adafruit

A value pack of three Adafruit Perma-Proto Quarter-Sized Breadboard PCBs. Each board mirrors the layout of a tiny solderless breadboard (plus power rails) with 5-hole connected pads, four power bus rails, and clear si...

SKU: AF-3244 | Brand: Adafruit

A compact three-layer round robot chassis kit with two DC drive motors, matching wheels, and a caster ball for balance. The high-strength anodised aluminium alloy frame provides a sturdy platform for building your own...

SKU: SF-COM-10349 | Brand: SparkFun

The FQP27P06 is a P-channel enhancement-mode power MOSFET rated for −60V and −27A. With a very low on-resistance of 70 mΩ and a gate threshold compatible with 5V logic, it is well suited for high-side switching contro...

SKU: AF-1831 | Brand: Adafruit

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will...

SKU: AF-1891 | Brand: Adafruit

Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (pr...

SKU: AF-641 | Brand: Adafruit

A 3-ply conductive thread made entirely from 316L stainless steel fibre. Thin enough to sew by hand with a medium-eye needle, yet strong and smooth — ideal for wearable electronics, e-textile projects, and sewable cir...

SKU: SF-BOK-12730 | Brand: SparkFun

With more than 60 practical and creative hacks, this book helps you turn Raspberry Pi into the centerpiece of some cool electronics projects. Want to create a controller for a camera or a robot? Set up Linux distribut...

SKU: DF-DFR0406 | Brand: DFRobot

INTRODUCTION The Arduino Motor Shield is based on L298 (a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors). It helps you drive two...

SKU: SF-BOB-12700 | Brand: SparkFun

This simple breakout board routes a female USB Type-A connector's VCC, GND, D−, and D+ pins to a standard 0.1″ pitch header. It saves you the hassle of soldering tiny SMD connectors when adding USB host or device conn...

SKU: AF-3203 | Brand: Adafruit

The Adafruit Perma-Proto Bonnet Mini Kit is a prototyping daughter board sized for the Raspberry Pi Zero. It plugs directly onto the Pi's 2×20 GPIO header and provides a grid of 0.1″ soldering holes connected in a fam...

SKU: AF-3406 | Brand: Adafruit

The Feather nRF52 Bluefruit LE is an all-in-one Bluetooth Low Energy development board built around the Nordic nRF52832. Unlike earlier Bluefruit Feathers that used a separate helper chip, the nRF52832 runs your appli...

SKU: SF-BOB-10031 | Brand: SparkFun

We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all 5 pins with a vertical microUSB connector for your prototyping nee...

SKU: AF-759 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male head...

SKU: AF-1982 | Brand: Adafruit

The Adafruit MPR121 Capacitive Touch Sensor Breakout provides 12 channels of capacitive touch sensing over I2C. The MPR121 handles all the capacitive filtering internally and can be configured for varying sensitivity ...

SKU: SF-COM-09772 | Brand: SparkFun

A standard 5 × 20 mm glass cartridge fuse rated at 5A / 125V AC. When current exceeds 5A, the internal filament breaks and opens the circuit, protecting your electronics from overcurrent damage. Compatible with standa...

SKU: AF-826 | Brand: Adafruit

A ribbon of 40 premium female-to-male jumper wires, 150mm (6") long, in 10 rainbow colours (4 wires per colour). Each wire has a 0.1" (2.54mm) female header socket on one end and a 0.1" male pin on the other, fitting ...

SKU: AF-3517 | Brand: Adafruit

Everything you need to get started with the Circuit Playground Express — a feature-packed, all-in-one development board that works with Microsoft MakeCode (block-based or JavaScript), CircuitPython, code.org CS Discov...

SKU: AF-1952 | Brand: Adafruit

These premium female-to-male extension jumper wires are ideal for making wire harnesses or extending connections between headers on PCBs. Each strip contains 20 wires (2 of each rainbow colour) in a convenient ribbon ...