Brands and Manufacturers

SKU: AF-1669 | Brand: Adafruit

Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclos...

SKU: AF-1756 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1755 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-2324 | Brand: Adafruit

The Adafruit Ultimate GPS HAT adds high-quality GPS and GLONASS positioning to your Raspberry Pi. Built around a PA1616D module, it provides precise location data and a built-in real-time clock (RTC) with coin cell ba...

SKU: AF-2430 | Brand: Adafruit

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also i...

SKU: AF-2442 | Brand: Adafruit

Need to make a tiny robot? This little micro servo rotates 360 degrees fully forward or backwards, instead of moving to a single position. You can use any servo code, hardware or library to control these servos. ...

SKU: DF-FIT0085 | Brand: DFRobot

This custom-designed plastic wheel has a rubber tire measuring 1.65" (42 mm) in diameter and is designed to fit the output shafts on our mini metal gearmotors as well as the Solarbotics metal gear motors. Teeth on...

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...

SKU: DF-FIT0121 | Brand: DFRobot

Jumper wires are one of the most important gear component for the tinkerer. Often underestimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really n...

SKU: AF-2717 | Brand: Adafruit

The TCA9548A 1-to-8 I2C multiplexer solves the common problem of needing multiple I2C devices with the same address on a single bus. It acts as a gatekeeper, routing I2C traffic to any of its eight downstream channels...

SKU: DF-SEN0129 | Brand: DFRobot

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smok...

SKU: SF-PRT-14017 | Brand: SparkFun

This 2x20 “tall” header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can en...

SKU: DF-FIT0314 | Brand: DFRobot

NFC Tag (13.56MHz) is widely used in electronic locks or customer identification as well as other systems where a small and easy to carry tag is desired.The tag contains a NXP S50 chip and an antenna, and is passi...

SKU: SF-PRT-11895 | Brand: SparkFun

A standard 8-pin female header with 0.1" (2.54 mm) pitch, designed for through-hole mounting. Connects with most standard 8-pin male headers. Specifications Pins – 8 Pitch – 0.1" (2.54 mm) Type – Female, through-...

SKU: SF-DEV-13903 | Brand: SparkFun

This is the LilyPad Rainbow LED strip, with seven LilyPad LEDs that are still attached to one another, letting you snap LEDs apart at your leisure to sew into clothing or whatever else you can dream up.The LilyPad Rai...

SKU: DF-DFR0026 | Brand: DFRobot

Here comes DFRobot's new Analog Ambient Light Sensor for Arduino or Raspberry Pi. Brand new design and much more convenient to use. This sensor help you to detect the light density and reflect the analog voltage s...

SKU: DF-SEN0127 | Brand: DFRobot

  INTRODUCTION This is a generic Arduino gas sensor. It has MQ2 probe which is able to detect LPG, i-butane, propane, methane ,alcohol, Hydrogen, smoke.It can be used in gas leakage detecting device in c...

SKU: AF-157 | Brand: Adafruit

IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for any microcontroller.To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to...

SKU: DF-DFR0300 | Brand: DFRobot

The Gravity EC (Electrical Conductivity) Sensor measures the conductivity of aqueous solutions, providing an analogue output for Arduino and compatible microcontrollers. EC measurement is essential for monitoring wate...

SKU: AF-3084 | Brand: Adafruit

Looking for an ultra-thin heat sink for your Raspberry Pi 3? Check out this nice and slim 13x13x3mm Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry ...