Brands and Manufacturers

SKU: AF-3057 | Brand: Adafruit

Polyimide Tape (sometimes referred to by the brand name Kapton Tape) is an interesting addition to your toolbox! Polyimide Tape remains stable across a wide range of temperatures from about −269°C to +400°C.&n...

SKU: DF-DFR0029-R | Brand: DFRobot

Press to release pleasure! Our redesigned digital push buttons come with LED, immersion gold surface, and bright colored hats. A captital D at left corner indicates that it is a digital sensor. An illustration of b...

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-COM-11372 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a blue lens. It has a typical forward voltage of 3.4V and ...

SKU: DF-DFR0332 | Brand: DFRobot

Make an air aerial propeller vessel, a cooling system, or spinning machine with this small fan module. It comes with a propeller, a 15,000 rpm motor and cable. Add flavor to your own interesting projects with this ...

SKU: SF-PRT-10897 | Brand: SparkFun

These are 155mm long jumpers terminated as male to male. Use these to jumper from any female header on any board, to any other female header. Multiple jumpers can be installed next to one another on a 0.1" header. Com...

SKU: SF-COM-12993 | Brand: SparkFun

This is an SMD 12mm square SPST button. What we really like is the large button head and good tactile feel (it ‘clicks’ really well). This button is great for user input or a good reset button on a PCB, heck, we use t...

SKU: SF-COM-12903 | Brand: SparkFun

Sometimes when you have too many choices, it’s hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that’s all you want. Well too bad, you are getting two of each!...

SKU: AF-3377 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: SF-SEN-12650 | Brand: SparkFun

The AD8232 SparkFun Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as a...

SKU: AF-756 | Brand: Adafruit

Transistors are powerful little electronic switches, and we really like these NPN transistors whenever we need to control medium-power electronics such as small motors, solenoids, or IR LEDs. We find them so handy, th...

SKU: AF-3393 | Brand: Adafruit

A dual-ganged 10K linear potentiometer with a built-in on/off switch — two components in one convenient panel-mount package. The dual 10 kΩ linear-taper pots share a grippy shaft that turns smoothly without shifting o...

SKU: AF-3468 | Brand: Adafruit

The Chip Quik No-Clean Liquid Flux Pen is great for all rework, solder, de-solder, and reflow applications! In particular this one is from the rework-champs at Chip Quik. Liquid flux helps solder to "c...

SKU: SF-PRT-09749 | Brand: SparkFun

A 2-pin right-angle JST PH series connector for through-hole PCB mounting. With a 2 mm pin pitch, this is the standard connector used on most single-cell LiPo batteries, making it ideal for battery-powered projects an...

SKU: DF-DFR0315 | Brand: DFRobot

FEATURESAPPLICATIONSSPECIFICATIONSNote: It has been newest Model: A1M8 --2017/5/15 DOCUMENTS SLAMTEC Website Development Kit SDK & Datasheet Related Rplidar Review by Gavin (@MechatronicsGuy) ICP-SLAM based on Rob...

SKU: AF-3610 | Brand: Adafruit

This cable is a little unusual, rather than having a USB A plug on one end, it has two Micro B USB connections! What is this for? It's for when you have a "USB On-The-Go (OTG)" device, and you want to plug in anoth...

SKU: AF-658 | Brand: Adafruit

This 5V 10A Switching Power Supply delivers up to 50W of stable DC power, making it ideal for driving LED strips, motors, CNC projects, and other power-hungry 5V devices. It accepts both 110V and 220V AC input, so it ...

SKU: LB-LS3779 | Brand: Little Bird

A pack of 10 general-purpose 2N2222A NPN bipolar transistors in a TO-92 package. The 2N2222A is one of the most widely used transistors in electronics, suitable for switching and signal amplification in a broad range ...