Arduino

SKU: SF-PRT-13010 | Brand: SparkFun

This is a simple 2x3 female PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

SKU: DF-DFR0359 | Brand: DFRobot

INTRODUCTION eClip is an innovative programming/testing tool specially designed for Makers. It solves the problem of prototyping wearable projects with ICSP and FTDI interfaces in limited spa...

SKU: SF-BOB-12941 | Brand: SparkFun

With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding a...

SKU: SF-DEV-12924 | Brand: SparkFun

The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. This USB programmer connects directly to the MicroView and lets you not on...

SKU: SF-COM-10613 | Brand: SparkFun

A digital potentiometer that lets you control a voltage divider with serial signals from your microcontroller. Wire it up like a standard potentiometer, then use digital commands to adjust the wiper position — no mech...

SKU: DF-DFR0376 | Brand: DFRobot

INTRODUCTION OCELL is a 0.5" micro OLED display designed for Arduino and other microcontrollers. This micro OLED display is small as the grown-up's fingernail- 0.5" only. It has 450cd/m^2 sc...

SKU: SF-COM-12792 | Brand: SparkFun

This is a 2x40 pin right-angle PTH header. This header can be broken apart with a fair amount of force to form smaller header formations. Don’t worry, it’s easy enough to break it where you need! Each pin has a spa...

SKU: SF-PRT-10375 | Brand: SparkFun

This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway hea...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: SF-BOB-10160 | Brand: SparkFun

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. Th...

SKU: AF-1918 | Brand: Adafruit

An analog UV light sensor breakout based on the GUVA-S12SD photodiode, detecting the 240–370nm range covering UVB and most of the UVA spectrum. An on-board op-amp amplifies the tiny photodiode current to a readable vo...

SKU: DF-KIT0111 | Brand: DFRobot

The Gravity Starter Kit for Arduino is a plug-and-play electronics toolkit designed for beginners and makers getting started with the Arduino platform. It includes a DFRduino UNO R3 microcontroller (fully compatible w...

SKU: SF-DEV-12587 | Brand: SparkFun

Here at SparkFun, we refuse to leave ‘good enough’ alone. That’s why we’re adding to our line-up of Arduino-compatible microcontrollers once more! The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on ...

SKU: SF-ROB-12567 | Brand: SparkFun

This buzzer is an add-on for your RedBot that gives your robot the ability to make awesome beep-boop noises or alerts when something interesting (or terrible) happens. The buzzer works by making use of two I/O pi...

SKU: AF-772 | Brand: Adafruit

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the Blue & White 16x2 LCDs we stock in the shop. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LC...

SKU: AF-813 | Brand: Adafruit

Design a clock, timer or counter into your next project using our pretty 4-digit seven-segment display. These bright crisp displays are good for adding numeric output. Besides the four 7-segments, there are decimal...

SKU: SF-DEV-09717 | Brand: SparkFun

The FTDI cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The VCC pins of this FTDI cable are configured to operate at 5V with 3.3V I/O. The FTDI...

SKU: SF-SEN-09674 | Brand: SparkFun

This very long force sensitive resistor - over 2 feet - has a sensing area of 0.25x24". This FSR from Interlink Electronics will vary its resistance depending on how much pressure is being applied to the sensing area....

SKU: DF-SEN0203 | Brand: DFRobot

The DFRobot heart rate sensor is a thumb-sized heart rate monitor designed for Arduino microcontrollers. This sensor is a pulse sensor which is developed based on PPG (PhotoPlethysmoGraphy) techniques. This ...

SKU: DF-DFR0030 | Brand: DFRobot

A digital capacitive touch sensor from DFRobot's Gravity series. It detects touch through the same capacitive sensing technology used in smartphones — even through thin cloth or paper. The sensor outputs a digital hig...