Arduino

SKU: AF-386 | Brand: Adafruit

The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no an...

SKU: DF-ROB0112 | Brand: DFRobot

DFRobot proudly presents Devastator Tank Mobile Platform, our newest track mobile robot platform. It is fully compatible with most popular controllers in the market such as Arduino, Raspberry Pi and so on. ...

SKU: AF-409 | Brand: Adafruit

Electroluminescent (EL) wire produces a beautiful aqua (blue-green) glow that looks like thin neon lighting. This high-brightness version uses the latest technology and is twice as bright as standard 2.3mm EL wire, em...

SKU: DF-ROB0117 | Brand: DFRobot

The Cherokey 4WD Basic Arduino Robot Kit is a perfect wheeled robot platform to build your own robot and to get started with Arduino Robot. With just a few simple steps of assembling the hardware and tuning the...

SKU: DF-SEN0177 | Brand: DFRobot

The Gravity Laser PM2.5 Air Quality Sensor uses laser scattering to measure suspended particulate matter concentrations in the air. It detects particles from 0.3 to 10 µm in diameter and outputs digital concentration ...

SKU: DF-SEN0162 | Brand: DFRobot

The Gravity Analog UV Sensor V2 uses a GUVA-S12SD photodiode to detect ultraviolet radiation in the 200–370 nm (UV-A) wavelength range. It outputs a linear analogue voltage signal proportional to UV intensity, making ...

SKU: SF-PRT-13010 | Brand: SparkFun

This is a simple 2x3 female PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

SKU: DF-DFR0359 | Brand: DFRobot

INTRODUCTION eClip is an innovative programming/testing tool specially designed for Makers. It solves the problem of prototyping wearable projects with ICSP and FTDI interfaces in limited spa...

SKU: SF-BOB-12941 | Brand: SparkFun

With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding a...

SKU: SF-DEV-12924 | Brand: SparkFun

The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. This USB programmer connects directly to the MicroView and lets you not on...

SKU: SF-COM-10613 | Brand: SparkFun

A digital potentiometer that lets you control a voltage divider with serial signals from your microcontroller. Wire it up like a standard potentiometer, then use digital commands to adjust the wiper position — no mech...

SKU: DF-DFR0376 | Brand: DFRobot

INTRODUCTION OCELL is a 0.5" micro OLED display designed for Arduino and other microcontrollers. This micro OLED display is small as the grown-up's fingernail- 0.5" only. It has 450cd/m^2 sc...

SKU: SF-COM-12792 | Brand: SparkFun

This is a 2x40 pin right-angle PTH header. This header can be broken apart with a fair amount of force to form smaller header formations. Don’t worry, it’s easy enough to break it where you need! Each pin has a spa...

SKU: SF-PRT-10375 | Brand: SparkFun

This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway hea...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: SF-BOB-10160 | Brand: SparkFun

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. Th...

SKU: AF-1918 | Brand: Adafruit

An analog UV light sensor breakout based on the GUVA-S12SD photodiode, detecting the 240–370nm range covering UVB and most of the UVA spectrum. An on-board op-amp amplifies the tiny photodiode current to a readable vo...

SKU: DF-KIT0111 | Brand: DFRobot

The Gravity Starter Kit for Arduino is a plug-and-play electronics toolkit designed for beginners and makers getting started with the Arduino platform. It includes a DFRduino UNO R3 microcontroller (fully compatible w...

SKU: SF-ROB-12567 | Brand: SparkFun

This buzzer is an add-on for your RedBot that gives your robot the ability to make awesome beep-boop noises or alerts when something interesting (or terrible) happens. The buzzer works by making use of two I/O pi...

SKU: AF-813 | Brand: Adafruit

Design a clock, timer or counter into your next project using our pretty 4-digit seven-segment display. These bright crisp displays are good for adding numeric output. Besides the four 7-segments, there are decimal...